ender 5 pro fan duct 3d models

Ender 5 Layer Fan Duct Remix for the Ender 5 Pro. Some Ender 5's have a different style fan which means these ducts need more or less screw structure. This remix remove the 'U' shaped screw holes. There is also a raised version that adds 3mm...

Some people, like me, were having trouble printing with certain types of materials, because of the supports. I did this remix, and manually placed some internal supports, however it does not interfere with the air flow, so you can print completely...

I manually put some internal supports, but it doesn't interfere with the airflow, so you can print completely without support. In the small lock that is on the outside, I also put a support manually, just remove it with a blade. ... Attention: I...

I found the standard cooling shroud on my Ender 5 Pro and Ender 5 Plus to be a little inadequate. I couldn't find a model on Thingiverse that seemed to match my printers, both of which have Microswiss direct drive extruders. ... This is a simple print...

... the frame. My extra light cooling shroud for ender 5: https://www.thingiverse.com/thing:6079627 My BMG direct drive mount: https://www.thingiverse.com/thing:6079570 Design inspired by the original Satsana: https://www.thingiverse.com/thing:4528533

Hotend and part cooling fan for the MicroSwiss Direct Drive. It is tight in the X direction but you wont loose any build volume, Y is at 46mm not larger than stock. BL-Touch location: X: +8mm Y: -23mm Stuff needed 2x 50x50x15 Fans 6x M3x5 (if you...

BL-Touch location: X: +8mm Y: -23mm Stuff needed * 2x 50x50x15 Fans * 6x M3x5 (if you dont have these M3x8 will work too) * 2X M3 insert (I used Ruthex if you have something else you may want to adjust the hole size for the part cooling duct) * 2x...

BL-Touch location:X: +8mmY: -23mm Stuff needed 2x 50x50x15 Fans 6x M3x5 (if you dont have these M3x8 will work too) 2X M3 insert (I used Ruthex if you have something else you may want to adjust the hole size for the part cooling duct) 2x M4x23  2X...

I didn't want to have my spool on top of my machine due to lack of space. But no easy way to guide the filament or being able to find one made me decide to make this little peg. You can hand thread a PC4-M6 fitting in the hole and use your left over...

Fairing with fan duct designed to have better strength and cooling, this device corresponds only for ender 5 plus printer with microswiss system. The file contains : STL file SATURN BTC file For proper operation of the system, turn the...

A fan duct for Creality Ender 5. It supports single or dual 5015 fans. I've used it for a while and it works fine. It's fairly easy to print and assemble. Should you break any part, it's quick to print again. It's not screwed on the backplate, it...

Wasn't really satisfied by the stock fan duct and thought I could improve on the existing alternatives on Thingiverse. I tried to keep the outlets as big as possible while preserving view on the nozzle. Fits the stock fan without the need to remove...

I re callibrated my ender 3 pro, from the flow rate to e-steps to x, y and z movement. After that and running this new fan duct... I got results you see in the pics. ...Running a stringing test i had 0 stringing, was very surprised but also very...

I decided to design a new fan duct with modifications to ensure enough room between print and fan duct as well as broadened the output to avoid too much air cooling in one spot. In my opinion it produced better printing results. ...You are welcome to...

This is a layer fan duct I design for my Ender 5, it spreads the airflow all around the extruder. It should work on Ender 3 too. ...It is very important to have a silicon protector on the extruder, if not, this part can be partialy melted.

This is a layer fan duct I design for my Ender 5, it spreads the airflow all around the extruder. It should work on Ender 3 too. ... It is very important to have a silicon protector on the extruder, if not, this part can be partialy melted.

This is a 360° fan duct for the Ender 5 with a support structure, that benefits airflow. If you like/use my design, please consider to tip me. I'm a student and even the smallest amount is always welcome and appreciated. ...Thank you!

This is a remix of the Ender 5 Cooling Duct" by McGybeer. I removed the logo. ...Also on of the parts where the screws go thru didn't fit so I removed that too

Simpel improved fan duct, exchange with standard one. ... Print without supports in vertical position

Simpel improved fan duct, exchange with standard one. Print without supports in vertical position Category: 3D Printer Parts

Successor of my previous design: https://www.thingiverse.com/thing:4363135 The air out lets are now symmetrically positioned around the nozzle and hot air coming from the hot end's heath sink is prevented from interfering with the model fan air flow....

... end clearly while printing. ...So I've rotated the duct to the back of the assembly, made room for the lower roller and added some internal vanes so you don't need to use supports. I made this for my E5+. ...I do not know if it fits other E5 models.

Airflow will be less concentrated, but the heat of the hot end will have less effect on the duct. The support is part of the design, and can easily be snapped off the print. You want to define your own support: use the file 'FanDuctEnder5-4_v19 - No...

fan duct for ender 3 pro with 40mm fan

fan duct for ender 3 pro with 40mm fan

Carénage avec fan duct conçue pour avoir une meilleur solidité et un meilleur refroidissement, ce dispositif correspond uniquement pour l’imprimante ender 5 plus avec le système microswiss. Le fichier contient : • Fichier STL • Fichier CTB SATURN ...

2in1 Fan duct and part cooling for Ender 3 / 3 Pro Simple and effective design.

Fan duct to greatly improve the air flow for print cooling without making major modifications to the machine. ... is mounted on the original fan.

-Screws 15mm and nuts Hotend fan to GANTRY -Screw 11mm and nut Fan Support IZQ to GANTRY to Gantry Support -Screw 10mm Fan Support IZQ to GANTRY to Ender Platen -Screws 14.5mm and nuts GANTRY to Gantry Support -Screw 12mm and Nut GANTRY to...

**Update 2022-12-12:** I made a far better version of this thing, you can find it **[here](https://www.printables.com/model/338566-hotend-fan-duct-for-ender-2-pro)**. **Summary:** I was annoyed by the noise of the hotend fan. To mount a quieter 4020...