ev charge plug holder 3d models

this is a wall mounted holder for mennekes type 2 (dostar) EV charge cable.

this is a wall mounted holder for mennekes type 2 (dostar) EV charge cable.

Wall mounted holder for Mennekes EV charge plug, provided with Volkswagen eUp first gen. The diameter of the handle is 42mm. ...

This is only the lower part from the "EV plug holder" by manny87. ...This part has been modified to fit the Hyundai IONIQ charging cable, or other thicker charging cables.

The charging cord that comes with the Chevy Volt gets mounted near an outlet, but I wanted the charge plug end near my car. MakerBot to the rescue! Designed in SketchUp, this bracket mounts to the wall near the car and provides a convenient place to...

The holder can be placed well next to the charging station (wall box) to hold the plug and the charging cable when it is not in use. The holder is equipped with a lock and can only be pulled out by pressing the button. We recommend for the printout...

The holder can be placed well next to the charging station (wall box) to hold the plug and the charging cable when it is not in use. The holder is equipped with a lock and can only be pulled out by pressing the button. We recommend for the printout...

The holder can be placed well next to the charging station (wall box) to hold the plug and the charging cable when it is not in use. The holder is equipped with a lock and can only be pulled out by pressing the button. We recommend for the printout...

Not really a remix, but a remake of the bottom part to hold the charging head of Kia / Hyundai charging box. ... The top part of original thing https://www.thingiverse.com/thing:1425959 works perfectly.

The plug seems to stay by itself quite nicely in the holder, which is made in TPU to make it easy to get the plug in and out. The cable hanger is made from PLA. The holder should keep the plug protected from the elements. ... No support required for...

This receptacle is a replacement for the J1772-style plug holder on the Schneider EVLink line of electric vehicle charging stations (ours is model number EV230WSR). The plug holders that ship with the charging stations seem to be pretty brittle and...

Made to hold the charge cable for my Tesla EV. I've printed it but I have yet to test it. The sliding mechanism to hide the screws is very thight but if you have a dimmensionally correct printer it will fit. There might be design changes to the...

The holder is partly a remix of https://www.thingiverse.com/thing:1425959 and https://www.thingiverse.com/thing:1894781

EV plug holder

A holder/port to hold an EV charging plug. ... Latest version adds a draft to the walls to improve strength.

This is an EV type-2 charging plug holder for when the plug is not in use. It is designed to screw to a wall or similar. I designed this when the one that came with our charger broke. It was just moulded plastic so I figured I could do better. ...It...

This is an angled J-1772 Plug Holder built on the work of MadTreevis. There are designs for a 30° angle and a 45° angle. ...The 45° version works best for my charger.

Electrical Vehicle plug holder. Holds nozzle type J1772. Rotates 180 degree, a convenient model for holding the nozzle in a tight location. ...Can be turned in parallel against the wall.

... printed with ABS or PET-G or other open-air resistant and a little flexible. ... It is an outside holder for temporary use or if you prefer this Plug position on your wall. ATTENTION! ...IT MUST BE PLACED ON THE BIG FLAT SURFACE ON THE PRINTER HOTBED

For Plug Type2 or 1 on wall placement.

It also stores the plug parallel to the wall so that it does not stick out into the drive like the purchased ones I have seen. It is for a type 2 plug. If you have any other type I will design one if you send me the exact measurements. Attach the...

EV Charging Plug

This is a remix of MadTreevis's J1772 EV Plug Holder for a vertical instead of horizontal application. I needed something to store the plug upright on the side of the garage stairs into the house, so mixed this up. ... Also provided the mirror image if...

This is a simple holder for a type 2 EV plug (Mennekes) and the cable. It has 2 holes for 8mm screws with washers and enough room for a 13mm socket in order to tight the screws. Designed to be printed with a 0.8mm nozzle. ...

This is an inner piece of the Ratio Electric Mennekes type 2 plug holder. ...It grabs the plug via a latch and is mounted spring loaded inside the plug holder. ...Mine broke so I fabricated this replacement part.

thanks to user s_kohls submission, especially with the fusion360 file, it was easy for me to create a slightly modification by tilting the plug slot a bit upwards. I preferred to let the force of gravity do the job of keeping the plug ;) my modified...

I tried a few of the Type 2 holders from Thingiverse but they didn't have the inner extrusion so they didn't hold properly. ...I made the screw holes the same as this one (66mm apart) https://www.thingiverse.com/thing:1621259 I created this from...

This is a plug template for the Type 2 (Mennekes) EV female charge connector. Meaning, the end of the cable that plugs into your car, plugs into this. Adjust the tolerance parameter for a good fit with your print. ... This design is fairly useless on...

Protects your Level 1 EV charge cable if you have to close your garage door on it. Prevents cord from being pinched by garage door. Allows cord to slide freely (just barely) while door is closed on top of it. Should fit most/all Level 1 charge...

Hook to hang charging cable of an electrical car, for example a Type2 cable. Re-designed from scratch because the source of the remixed thing was not available. ...Prints with 0.2mm layer height and without any special settings.