fanatec pedal 3d models

These are some pedal plates I designed for my Fanatec CSL pedals with Load cell. I decided to invert my pedals and was sick of the stock pedal design. These pedals are based on simworx pedal plates and are designed for heel-toe technique in mind. ...

When I made this design the LoadCell option was not available for the Fanatec CSL Pedals. Anyway for anybody who likes DIY project it still can be an option :) Parts you will need: - load cell (50kg in my case) - 608 bearing (22mm x 7mm) - 1...

Replacement flexible grippy pedal cover for Fanatec CSL pedals. Print in TPU. The model is sized for an extremely snug fit, and you will have difficulty putting it on. Use a screwdriver or trim tool on the back, to pull the TPU lip over the...

This is a Protection Cap for the rumble motors on the Club Sport Pedals, if you have to mount them upwards.

I created inverted pedals since for the fanatec csr pedals since I didn't want to buy the brackets sold by fanatec. The only problem with the design is that I totally miscalculated the opening where part of the pedal assembly will slide into by 4mm...

(TPU for sound damper required) You need 4x M6 60mm Bolts and 4x M6 Nuts and a set of RC Car Damper with 140mm length like these: https://aliexpress.com/item/32603488386.html If you want an even stiffer gas pedal you can also order these (2.0mm +...

I wanted to add a damper to my Fanatec V3 pedals and decided to make my own. I order two dampers off Aliexpress for $5 each. I created the files in Fusio360 and printed on a Bamlu Lab X1C.

The basic stamped steel Fanatec CSL pedals have a M6 threaded collar on the underside of the heel plate. But its not planar with the bottom of the pedal assembly, its only about 12mm tall from the underside of the heel plate. So I made this spacer...

These are clamps for the newest CLS Pedals delivered e.g. with the Fantatec GT DD Pro. For mounting on the PlaySeat Challenge. ... Material List: 2 M6 * 30 mm screws (for the front clamps) 8 M4 * 20 mm socket head screws 8 M4 Nuts 2 M5 * 16 mm...

This spring increases the force required to push the break pedal and makes it feel better (IMHO). Printed in PLA and works fine, scrubs a bit in the beginning due to the inner diameter of the holder. This will wear out and become quiet after a few...

Fanatec elite pedals. ...Measurements fairly accurate.

I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting...

I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting and...

snaps on and off your pedals and allows you to attach extensions without making changes to your pedal. only works with Plastic front plates. ...https://www.youtube.com/watch?v=7bJZTANVYdc

I use rumble motors on 4 corners of my rig to simulate corner vibrations & found having them on the pedal itself a bit annoying. Remove the end cap from the pedal body & fit the rumble mount in its place. You'll need to mirror the STL files in your...

These mounts allow the Dayton Audio TT25 transducer (bass shakers) to be mounted to the Fanatec CSL pedals.  There is a separate model for the accelerator and brake pedal.The mount is secured to the TT25 via M3x15 bolts and then the entire unit...

Base/Support for Rumble Motor mount that fits to Fanatec CSL Pedals by using the fanatec's factory screws. For mounting the motors on my base, i borrowed the design below from kazukiorg: https://www.thingiverse.com/thing:5142613 You will need...

Fanatec CSL Pedal Kit (w/load cell) Brake & Accelerator Mods Hi everybody! This is my second project shared to Thingiverse. Feedback is welcome - I hope this comes in handy for someone who was looking for what I was. This design was inspired by...

# Universal Playseat Challenge Fanatec Pedals Mounts After breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. This universal mount allows you to affix both Fanatec...

Universal Playseat Challenge Fanatec Pedals MountsAfter breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. ...This universal mount allows you to affix both Fanatec V3...

I liked the original design, but it didn't fit my CSL pedals that came with the Fanatec DD Pro. I managed to use the original part for the front position (closest to the chair) and I remixed the design for the rear position, so the pedals can be...

A simple adapter to mount TT25 PUCK bass shaker on the brake pedal of Fanatec ClubSport V3 pedals. ... More details in the video: https://youtu.be/al3gEAN6RiI

Based on the video posted by amstudio https://www.youtube.com/watch?v=8aLqqcEaUVk&index=4&list=PLW_mVHJcIJmFL9AQvqOPWl9R9LVWlCZAX&t=399s my contribution is the rumble motor holder for the Fanatec CSL elite pedals with load cell. The design is based...

https://youtu.be/9lxu1R-dmdc ressorts utilsés: https://www.conrad.fr/p/5-ressorts-x-l-225-mm-x-815-mm-889249 https://www.conrad.fr/p/5-ressorts-x-l-27-mm-x-885-mm-889247

A wrench to help adjust the break preload of the FANATEC ClubSport Pedals V3

https://www.xsimulator.net/community/threads/fanatec-clubsport-pedals-v1-and-v2-mods.14492

i was doing service on my Fanatec Clubsport V3 pedals and noticed my hydraulic damper was missing a bolt and a shim spacer thing. the other side was still there so i made one. the original bolt was a M4x6mm bolt. i had M4x8mm bolts so its made for a...

This is for vibration motors mount that fits to the Fanatec Clubsport v2 pedals. It will also fit to v1 and probably v3. The original vibration motor was removed. You can use it for all three pedals. You will need longer screws to mount the mount. ... ...

This is a board holder and hall sensor holder for my Fanatec Clubsport V1 Pedals using Leo Bodnar Electronics. The hall sensor simply fits into the rectangular gap and is held in place with some hot glue. I put the top of the sensor flush to the...

If you're like me and somehow lost the little spacers inbetween the Hall Effect Sensor and the pedal on the throttle or clutch pedal then you're in business! These are to scale models of them so you can print some. Note that because of it's size,...