firefly board game card holder 3d models
687868 3d models found related to firefly board game card holder.thingiverse
Customized version of http://www.thingiverse.com/thing:94611 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=94611 Instructions Using the following options:...
cults3d
Recently bought the Firefly Board Game and felt like all the decks, money, and tokens took up too much table space. So I designed and printed these holders. The Nav Deck Holder Lid needs to be made a little narrower by about 3.5mm. Game Piece is a...
thingiverse
Made and Printed holders for all my cards in the Firefly Game, but still had the Encounter card floating around the table, so made this little holder to make it fit in with the game. ... Made it with the little nubs to hold the card in the slot, if they...
cults3d
Card Holder with double line for cards , each line with capacity for: 5 american standard cards or 4 Standard cards (MTG) or 6 mini american standard 5 spots for tokens large 277 mm width 50 mm height 19mm
thingiverse
The Firefly board game takes up a lot of space. This caddy will help players keep their ships organized. It has slots for Upgrades, Jobs and Cargo. There's even additional Cargo and Stash slots, in case the player gets an upgrade later on. The oval...
thingiverse
For those who owned 2nd printing ROOT Board Game onwards, you only have 1 card holders instead of 5 Use this to print your own card holder Can be used for a general purpose card holders too! ... I designed this to be used with this great insert:...
thingiverse
Scythe Board Game Card Holder I reduced the mass of this card holder by about 100g: https://www.thingiverse.com/thing:3086696 I cut the sides open, added storage holes below the cards,and reduced the walls to 0.96 mm thickness. Printed at 0.32 mm...
prusaprinters
Scythe Board Game Card Holder I reduced the mass of this card holder by about 100g: https://www.thingiverse.com/thing:3086696 I cut the sides open, added storage holes below the cards,and reduced the walls to 0.96 mm thickness. Printed at 0.32 mm...
thingiverse
I am working to resolve this issue.** **A customizable card holder for your favorite board game!** The holder has a sloped bottom to hold cards in. A "finger" cutout in front allows for easy retrieval of the entire deck. Negative space in the floor...
thingiverse
This is a set of card holders for the game Dungeon!, the D&D board game. Instructions I've been sitting on this since Jan 2013 because I wanted to print it before I posed it. Alas I haven't found the...
cults3d
... the plastic blister that holds all the components. It is very possible that this card holder can also work for board games that use cards similar to the ones Takenoko has (4.5 x 6.5 cm), if you don't mind it having "Takenoko" written on it... ...:)
thingiverse
It is very possible that this card holder can also work for board games that use cards similar to the ones Takenoko has (4.5 x 6.5 cm), if you don't mind it having "Takenoko" written on it... :) ...
thingiverse
... lately so I decided to make a little something to make my setup and teardown of the game a little easier. ...This card holder was designed to be stackable, fit into the original gizmos box, and provide easy access to the cards during game play.
thingiverse
Space extenders for board games to fit expansions and extra 3D printed tokens. ...This one is specifically measured for the Firefly board game, But can easily be stretched up or down to accommodate other games. ...This is a very snug fit.
thingiverse
Card holder designed for Descent 2nd edition, but it will hold any 41mmx63mm cards. Printed on Prusa Pro with 0.2mm layer height. ...Enjoy!
thingiverse
This is a card holder that I made to hold your draw deck and discard piles. ...This is made for NO CARD SLEEVES.
cults3d
This is a card holder from Doc Seven's deck 77. The dimensions of the cards are 11 cm x 7 cm. The coin has a central hole underneath, to allow the player to push the cards out, all while being optimized to consume less filament. ... This way there is...
thingiverse
A smaller version of my other card holder, Scaled for the treasure deck in Talisman, Tall enough to hold all the treasure cards from the original box (Unlikely to hold any expansions) This has locating lugs so that they may be stacked. ...This has not...
thingiverse
(Thanks JediKep!) He also introduced me to a Firefly community and a new board game. Some of the ships in the game are not represented by game pieces (models). So, with pictures from the game, I've created these 4 models and a board game peg for...
thingiverse
I got the idea for these from the token trays designed by IrishRock1987, but they didn't include the expansions for the game. I printed them all and tested them with the tokens from the base game and all the expansions. For a few of the token...
thingiverse
Ideal for board game cards where you need to see the entire card like King of Tokyo. (playing with kids they need to often see their cards and read them) Fits 4 cards up to 65mm wide each. print as many as you need if you need to hold more than 4...
thingiverse
While there are several great deck holders available, unfortunately they didn't work so great for the cards when they had a card slip over them. I also wanted to practice with Fusion 360, so I made this design. Considering that this is my third...
thingiverse
**NOTE:** The contact and supply deck holders will accommodate 10mm of cards (starter game plus Breakin' Atmo). Some expansions add additional cards. The Burn deck will accommodate 14mm of cards which covers the Alliance Space, Border Space, and...
thingiverse
This a holder for the Orleans board game round cards
thingiverse
Customized version of http://www.thingiverse.com/thing:94611 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=94611 Instructions Using the following options:...