flexible filament extruder 3d models

This extruder is made to print flexible filament with the aluminium extruder. The tolerance between the gears are Really small, it might even touch it. You don't really need specific tool beside the 2mm and 2.5mm allen wrench included with most of...

(less then before tho)The main cause of problemes:-the filament is to much flexible (ex:ninjaflex)-to much restriction in the bowden-to much restriction in the hotend:-clog / partial clog-low tempThis extruder is made to print flexible filament with...

The clamp holds the bowden coupling in place using M3 screw/nut Print Settings Printer: flashforge creator pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 80% Notes: I ran a 2mm drill bit through the filament path to open up the hole from any...

This is a flexible filament extruder with a 3,98mm PTFE-tube diameter for a better fit.

Product description This is a remix of B-Cup's Tevo Flexible Filament Extruder Upgrade with tighter tolerances in the idler pulley side. Compared to the previous version, this one: 1. Reduces the risk of extruder jamming. In my case, from 1 jam...

Product description This is a remix of B-Cup's Tevo Flexible Filament Extruder Upgrade with tighter tolerances in the idler pulley side. Compared to the previous version, this one: 1. Reduces the risk of extruder jamming. In my case, from 1 jam...

I totally re designed it from scratch and this version is solid: https://cults3d.com/en/3d-model/gadget/flexible-filament-extruder-with-wire-holder-v3 This is a updated extruder with a wire holder attached. You will need to get a longer screw for...

Previous remixed ver: https://cults3d.com/en/3d-model/gadget/flexible-filament-extruder-with-wire-holder Instructions: 1) Prepare some PTFE tubing as described in this CHEP video: https://youtu.be/az7pysnV_MY?t=112 2) Get an M3 16MM screw, the...

I modified the original extruder from Velleman to be able to print flexible filaments. It comes in place of the original extruder, no modifications or new hardware needed. In order to load the flexible filament, you need to demount the extruder. ...

Extruder suitable for flexible filaments. Designed to be used with stock extruder parts from MicroMake D1 Delta printer. Added a body STL with looser tolerances for printers that struggle with small holes. Supportless idler added. ...2 Piece Idler...

I made a new extruder top for the Bowden extruder that came on my Tevo Tarantula so it will feed flexible filament. I have not tried Ninjaflex, but it works great with Makerflex from Makergeeks. As you can see in the photo, it is basically a copy...

His upgrade did not work for me, with my modification there is no space left where filament can bend or get stuck. I have printed the big chainmail from (https://www.thingiverse.com/thing:3096598) FLOWALISTIK in TPU with my version of the upgrade...

V4 is a great combination with thirdhorizon's Printrbot Flexible Filament Direct Drive Extruder http://www.thingiverse.com/thing:403438 V3 helps in combination with EricPrint's Printrbot NinjaFlex Pilot Upgrade...

It will allow this printer to print with flexible filament more reliably using a PTFE insert to close the gap in the extruder that normally allows TPU to get jammed. This project requires a 13mm section of PTFE tube for 1.75mm filament cut to a point...

I designed these extruder for Anet E10, with finer tolerances to use flexible filament. In the photos, we see them assembled with the Anet E10 Filament Quick Change Tool (https://www.thingiverse.com/thing:2551264) I also replaced the original tube...

... now where it was plunging in and out 2 mm before. You still need a little PTFE snippet for the front filament guide. These work great for flexible filament. ...Chep covers the original one here https://www.youtube.com/watch?v=az7pysnV_MY

This is an upgrade for CR-10, It will allow these printers to print with flexible filament more reliably using a PTFE insert to close the gap in the extruder that normally allows TPU to get jammed. ... I used this video as tutorial:...

The original flexi filament extruder missed a good support for the hotend cables. Just added a simple ring to the original project. I used tinkercad to fuse the two item together. ...

This Model helps me to solve the problem printing flex filaments with my FLSun Cube.

This is a updated extruder with a wire holder attached. You will need to get a longer screw for this section. It should be 3mm longer than the original screw. ... This is a remix with the addition of http://www.thingiverse.com/thing:3034224

This is a updated extruder with a wire holder attached. You will need to get a longer screw for this section. It should be 3mm longer than the original screw. It was designed for the Creality Ender 3. I printed this with PLA with a layer height of...

This is a remix of the Improved Flexible Filament Extruder Upgrade CR10, CR10 Mini, Ender 3 by Elproducts. This has no need for a PTFE tube that need to be cut. It works on my Ender 3 with both flexible filament and non flexible filament like ABS &...

This is a remix of the joshvv Flexible Filament Extruder Upgrade that I added M6 threads to the inside hole where the coupling attaches to prevent the coupling from popping out when not using flexible filament on the printer. I had this happen...

This is a threaded version of Flexible Filament Extruder Upgrade. I had trouble connecting the Boden tube to the original version. It would not "self thread" and would disconnect from the part when printing began. So I imported the original model...

Material Petg: https://vk.cc/9aGn9Q

I use M6 ptfe coupler in this design.

I printed his and my flexible filament still got jammed out the sides of the extruder. ...I personally didn't like the idea of the extra "tube" style since my filament still managed to escape, so i started from scratch on NX7.5 and created a precise...

- insert the PTFE tube with the appropriate cuts for extruding flexible filament - install the bracket onto the z-axis bracket with the extruder arm - insert the M5 washer against the stock arm where the spring goes (without this, the spring will...

I was having difficulty printing with some flexible filament out of the box with the Creality Cr-10s Pro, so tried out some of the mods on here, but none of them really worked. Here, I've mashed a few of the designs I found together to have...

This extruder helps close the gap between the extruder gear and the bowden tube. It allows you to push the bowden tube through the fitting, and trim it to match at the extruder gear. I would dry fit the bowden tube before fitting it through the...