flite test a10 3d models

Unfortunately one of the wheels fall of on my E-Flite UMX A10 on intial setup of the airplane. This spare parts can be drilled with a 1mm drill and then put on the axis. ...Pls fix it with glue if you want to keep all wheels :-)

Flite Test Logo stencil for spray painting or airbrushing.

Engine for the Flite Test Corsair Master Series

A simple printed replacement for the plywood firewall used in Flite Test model plane construction

Here is a faithful reproduction of the Flite Test firewall used in many of their designs.

Did you get the power pack B from flite test? ...place this shim between motor and motor holder. https://store.flitetest.com/flite-test-power-pack-b-radial-edition-flt-3059/p983485 https://www.eclipson-airplanes.com/standardpowerpack

I just made the screw holes wider so the X Mount on the Flite Test B Pack would fit better.

Motor firewall for the Flite Test swapable power pod. ... http://flitetest.com/articles/ft-swappable-power-pod-kit

80mm diameter wheels with a 2.6mm axle hole. ...I made these for some of the Flite Test planes but use them for whatever you want :D

A simple printed replacement for the plywood firewall used in Flite Test model plane construction Instructions Just print at 50% or more.

Flite Test Logo. Printed like 15 % infill. I used a 3D Printer called the Flash Forge Creator Pro. ... How I Designed This Auto Cad Then Inventor to my printing software.

Here are a few parts for building your Flite Test RC airplanes. The pieces should be pretty identical to the originals. I'll have a few more up soon and will expand this summary. ...

I built one of the Flite Test minis and needed the motor mount and small pod. ...I just hand drilled the side holes after printing with a 1/8 bit to male them fit the skewers exactly.

Use in place of the plywood firewall Flite Test designs use. Will fit the standard FT power pod and swapable power pod. Intended for brushless electric motors. Probably not suitable for gas engines. Note: I model knowing the limitations of my...

This is a battery holder to mount to the bottom of the power pod used on a variety of Flite Test models. I'm using this one on a bloody baron. You can attach it to the bottom of the power pod with double sided foam mounting tape or hot glue. ... ...

3D Printed a custom firewall for the Flite Test Bushwacker power pod. Motor mounting holes are 30mm apart, and slightly offset downward. The skewer holes on the top are spread out to accommodate the larger motor. For my particular case, the motor...

These are hinges for Flite Test foarmboard RC aircraft. I have several aircraft where the original foamboard hinge is giving way. I could use tape or maybe hot glue but the paper is also loose so decided to (tape the edges) and print a more solid...

Formers for the Flite Test Master Series Spitfire. Printed with two top and bottom layers, two walls as well as 2% infill (I used alternating layer lines), these came out comparable in weight and strength to foam pieces and are a lot easier on the...

This is a battery holder to mount to the bottom of the power pod used on a variety of Flite Test models. ...I'm using this one on a bloody baron.</p> <p>You can attach it to the bottom of the power pod with double sided foam mounting tape or hot...

This is a frame for the Flite Test Gremlin micro brushless quadcopter. Currently using 2mm screws for standoffs and 1.4mm screws for motors. The frame is 3/32" thick, the same as the G10 frames Flitetest is selling. I don't have a Gremlin, as I...

Battery cover replacement for the Flite Test Tutor. Mine fell off mid-flight and I figured I would just design a cool one instead of a simple foam replacement. Offers 6 spots for 5x2mm round magnets, as well as 3mm skewer holes to keep it in...

Formers for the Flite Test Master Series Corsair. Printed with two top and bottom layers, two walls as well as 2% infill (I used alternating layer lines), these came out comparable in weight and strength to foam pieces and are a lot easier on the...

These are winglets for the FT Dart foamboard aircraft from Flite Test. They are modelled after a Boeing 737! They look sweet and actually help straighten out the yaw instability that most wings encounter. The files are for the left winglet. Just...

Flite Test Style power pod I designed this to be printed with minimal overhangs, since I seem to suck at calibrating my printer for bridges. There are other lighter designs on thingiverse, but my printer doesn't print them well. if you can handle...

Flite Test Logo stencil for spray painting or airbrushing. Print instructionsCategory: 2D Art Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: .2 Filament: Hobbyking PLA Notes: At .2 resolution this stencil is...

I liked the Flite Test Viggen except for the foam board nose. It was not very pretty nor was it very scale. It was also a PITA to build. But the concept of a disposal/replaceable nose was appealing. So I 3D printed one along with some modification of...

Elite Test Swappable Firewall, it is 5.1 cm wide by 4.35 cm tall by 2.4 mm thick

Flite Test Firewall

Flite Test Spitfire canopy frame

This is a mini power pod that replaces the original Flite Test foam + wood mini power pod.