fpv drone gopro mount 3d models
375855 3d models found related to fpv drone gopro mount.thingiverse
Made a mount for gopro hero 6/7/8 etc. because I did not find any that was nice and small and had a bottom plate that would allow me to screw in the mount to the frame rather than zip tie or velcro it on. I made a tiny alteration to the STL file...
cults3d
This GoPro Session Mount was build for a 220mm drone. The screw holes are .118in and the distance from the middle of each is approximately 1.655"x1.151". The slits on the side should fit any standard battery strap. I have sliced it for two reasons...
thingiverse
This GoPro Session Mount was build for a 220mm drone. The screw holes are .118in and the distance from the middle of each is approximately 1.655"x1.151". The slits on the side should fit any standard battery strap. I have sliced it for two reasons...
thingiverse
this is a model that i desinged for my 250mm fpv quad. Its pretty basic and sits on a 20 degree angle. you can use double sided tape and zipties to hold your go pro down. ...i use a go pro hero 3+
thingiverse
GoPro style mount for DJI FPV drone. 6 point mount. ... This thing wasn't tested yet.
thingiverse
There were only GoPro session mounts on Thingiverse so I decided to make my own for those who dont want to spend 15 dollars on something that someone else will 3d print. This mount fits the XILO Phreakstyle 5 inch body. It may fit other XILO bodies...
thingiverse
Designed for geprc mark 5, I dont know if it goes on the old ones? Has the camera bracket been updated? Put holes on it so you can strap the gorpo to be done worrying about it drops out in air 15 30 and 45 degree tilt angle, a bit extreme I...
thingiverse
GoPro mount for Diatone Tycan cinewhoop
thingiverse
This is a 3d printed (TPU) Action Cam mount for DJI FPV drone. You need a threaded insert m5x6mm and a m5 screw from some other mount you own or just a normal m5 screw :D .. if you dont have a threaded insert you can use a normal nut. i will add a...
cults3d
A GoPro Session mount for 220mm FPV drones. The screw holes are a tight fit. ...I recommend using a longer than normal battery strap also to hold your GoPro In place.
thingiverse
A GoPro Session mount for 220mm FPV drones. The screw holes are a tight fit. ...I recommend using a longer than normal battery strap also to hold your GoPro In place.
thingiverse
... M5 Nut rather than threaded insert. ... Original: https://www.thingiverse.com/thing:4799510 See original for all other settings. https://www.instagram.com/reel/CPh4fAIBfL5/ Is footage shot using this mount ,Hero 9 and RSGO for stabilisation. ...
thingiverse
Designed for the Wicked Quads Phanta FPV drone. Mounts onto 30x30mm with M3 mounting holes. ... Buy it here: https://www.wickedquads.com
thingiverse
Gopro mount for fvp drones with frame revenant For any changes or parts of different sizes do not hesitate to contact me! ...:)
thingiverse
This is designed around the GoPro Hero 4 Session -35 degree angle -Velco slot -Zip ties grooves for securing to aircraft
thingiverse
lock designed to prevent patio umbrella from spinning around when tilted to block the sun. designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is...
thingiverse
This is a gopro/action cam mount that fits all styles and sizes e.g. ...it can fit gopro session and gopro hero its made for the qav But fits most other mounts and those that dont fit just need a little sanding or drilling enjoy!
thingiverse
Insta360 GO 3 FPV Drone Mount compatible with GoPro mount base. Please use TPU. ... https://youtu.be/T2k64NToGvE
thingiverse
Made on request for @heropsycho 30 degree mounting angle. ... Optimized for sturdiness over vibration reduction Print with TPU at desired infill (100% may be hard to get gopro in and out)
thingiverse
Print this if you need to attach your GoPro or other action cam to the "typical" GoPro mount for your FPV drone. Please just let me know if you need this on your frame and let me know the dimensions of the hole pattern. ... Currently available...
thingiverse
This is a simple mount to attach a GoPro Hero 3 or Hero 4 to a racing drone. It works on a drone with a top-mounted battery, because the battery holds the mount firmly in place. This means that the camera mount is also easily removable, so you do not...
thingiverse
Made this to mount my Gopro to my Ummagawd freestyle FPV drone, could be mounted to cars etc.. with double sided tape. ... Need to flip it onto it's flat surface to print.(bottom)
thingiverse
Mount for drock frame Source file was the one for the TBS Source one, I just changed the part below to fit the Drock mount.
thingiverse
Get Skull and Drones Racing Frames here: http://goo.gl/OQuZpm Universal 20° angle for Skull and Drones RAMPAGE http://goo.gl/OQuZpm