ft explorer 3d models
14716 3d models found related to ft explorer.thingiverse
Just drawed some parts to make the ft explorer easier to build, and make it more rigid when building with depron 6mm.
thingiverse
this is nose gear for ft explorer. For assembly you need 8mm diameter aluminum tube 80mm long, spring and m3 screws. ...dont need any supports
thingiverse
Motor Mounts for FT-Explorer Type Pusher motor Print Settings Rafts: Doesn't Matter Supports: No Resolution: Medium Infill: 80-100% Notes: Printed ABS Head Temp 243 Bed Temp 90 on Blue tape
thingiverse
These are a few of my FT Explorer designs that have made the plane much more manageable and long-lasting. 1) Chassis - This is a wire chassis used to hold the electronics inside the body of the FT. It will hold a flight controller with a mount...
thingiverse
Here is the original Flite Test Explorer intro video from 2015: https://www.youtube.com/watch?v=BRxpozxGVEg Haha, the link to the FliteTest Store Explorer page from the above video is broken, here is the correct link:...
thingiverse
Parts for the Flite Test Explorer. I added support disks for the wing hold down dowels. ...Cam and VTX mount here: https://www.thingiverse.com/thing:3075182/files
thingiverse
My version of a 3D printable Flitetest Explorer motor pod. Also included is a mount for the Emax CF2822. Which is the motor I use the most. It will also fit the other Emax CF series motors. Tabs may need filing to fit properly. No thrust...
thingiverse
Very important / Muy importante The measurements of LANDER_TAIL_ft_EXPLORER.stl must be (35x35x30) mm and the measurements of the NDER_TAAIL_ft_EXPLORER.stl must be (35x35x2) mm. ... Las medidas de LANDER_TAIL_ft_EXPLORER.stl deben ser ( 35x35x30)mm y...
thingiverse
Replacement for foam FT Explorer nose cone. Models with and without mount for FPV camera. Should friction fit most FPV cameras with a 15mm square circuit board. F360 file included. Designed to print most of the body as single perimeter w/ .3mm...
thingiverse
These 3d printed parts make up for the assembly of VTOL (vertical take off and landing) mechanism for FT planes, specifically for the FT explorer/Bronco. These parts are revision 2 of my old design. To be printed PLA/PETG/PC. Minimal to no sanding...
thingiverse
This is a remix of the excellent original design by FooRider. I found that the rear "hood" of the mount didn't provide enough clearance for the prop after mounting the engine so I moved the firewall rearward approximately 1 cm and it will accomodate...
cults3d
Motor mount for FT Explorer! ... Link to FliteTest site: https://www.flitetest.com/articles/ft-explorer-build Link to motor + esc + servos: http://ali.pub/4nfuov
thingiverse
This is a motor mount and a control horn for the ft explorer. ... The foam board plane plans and DIY instructions can be found here. https://www.flitetest.com/articles/ft-explorer-build
thingiverse
This is a motor mount and a control horn for the ft explorer. ... The foam board plane plans and DIY instructions can be found here. https://www.flitetest.com/articles/ft-explorer-build
thingiverse
Nose wheel mount, main gear mount, and motor mounts for use on the FliteTest Explorer RC airplane kit print nose wheel mount with the sloped face down so that no supports are required. The control horn mounts with the control arm down so no...
thingiverse
This removable tricycle landing gear is designed for the Flitetest Explorer or Bronco. It uses a dedicated servo to control the nose wheel. The landing gear I used was Main gear ...
thingiverse
Simple parts to protect your FT Explorer wings from getting rubber band indentations on the leading/trailing edges. I glued mine in using CA glue (Super Glue) to keep the wing from sliding around inside of them. ... Works well!
thingiverse
UPDATE: 08/19/2018 - uploaded a corrected stl, Firewall Mount Plate.stl file, slots for mounting motor were off slightly. Units: inches Print each half flat side on bed of printer. Note orientation of motor mount plate (half circle to the top).
thingiverse
this lander gear need to be stick in the body of the plane whit clips
thingiverse
aseembly details https://www.thingiverse.com/thing:3599416
thingiverse
31 mm width to fit with 6mm depron built. 31 mm de large: convient pour une construction depron 6mm. Fichiers solidworks joints pour modif! ... Bon vols !
thingiverse
Battery tray similar to the FT Elements tray. ... Battery strap hole spacing and overall size are based on the build plans for the FT Explorer. ...http://store.flitetest.com/ft-elements-battery-camera-mount/
sketchfab
Here a conceptual exploration Vehicle i created in my spare time ! ...It is supposed to be a hybrid between an Airborne and Underwater Vehicle :D
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_outline_width = 0.5 text_thickness = 4.2 outline_thickness = 3.0 character_spacing = 1 bar_style = surround_text font_with_style =...