gamecube on raspberry pi 3d models

... printed it just waiting on a few small parts to assemble then I'll upload some pictures. I used a Pi4 4GB - Update 1-26-2021 Moved the power button to a more stock location, added a few design tweaks and a Raspberry Pi logo. ...All files reloaded.

Turned "original" cover intro fan grill and added Nintendo Gamecube logo. ... FreeCAD files are provided

Eng: This holder was designed to accommodate a Raspberry Pi Pico, and then be installed on top of the Memory Card B slot in a Gamecube. I suppose it could be repurposed for other things as well. Warning: These models were made in Blender with lots...

This is a remix of Sparrows89's amazing Gamecube Pi Classic and TheJeffChen's equally amazing Logo Dunk Corner Stand. I opened the vent holes on the sides and put some holes under the PCB (my Pis tend to run very hot - so I'll take any ventilation...

This is a remix of Sparrows89's Gamecube Pi Classic and TheJeffChen's Logo Dunk Corner Stand.I've previously remixed this case for the RPI3B and decided that I wanted to make it for my RPI4B, too - and while remodeling it to fit the 4B, I also fixed...

This is a remix of Sparrows89's Gamecube Pi Classic ( https://www.myminifactory.com/object/3d-print-gamecube-pi-classic-45314 ) and TheJeffChen's Logo Dunk Corner Stand. I've previously remixed this case for the RPI3B and decided that I wanted to...

I'm a big fan of the Nintendo GameCube, it's my favorite console. I recently got into 3D printing and decided to try my hand at making a new bottom parts shell and this is what I came up with. I hope that everyone likes it! ... Parts list 4x Cabo...

Slim holder for an raspberry pi on a 35mm x 7,5mm DIN rail Schmale Halterung für das Raspberry Pi (und alle anderen PCB mit dem Lochmaß von 49mm x 58mm) an eine 35mm x 7,5mm Hutschiene DIN EN 60715(veraltet:DIN EN 50022) Instructions you will need...

--- Yet another raspberry pi sleeve case remix. I wanted a case/sleeve that I can snap on or off but will not slide up or down. This case will easily come off if moved side to side, but is snug vertically, making it easy to plug or unplug usb...

raspberry pi on vesa 10cm X 10cm

Raspberry Pi 4 System on Chip

raspberry pi on vesa 10cm X 10cm

... be a fun and easy print as well, with even moderate settings it should only take a day or two of printing until it can be assembled. This has also been made to fit a Raspberry Pi B+, meaning you could easily turn it in to a Retropie console as well.

Step - print the gamecube logo - color white - load file Gamecube-Pi-Logo.stl - position the part at X0 Y0 Z0 on build plate - print the part 2. Step - print the disc cover - color black - load file Gamecube-Pi-Disc-Deckel.stl - position the part at...

Only remove the part from Cura Step - print the gamecube logo - color white load file Gamecube-Pi-Logo.stl position the part at X0 Y0 Z0 on build plate print the part Step - print the disc cover - color black load file Gamecube-Pi-Disc-Deckel.stl...

This is a little bracket I made for holding a Pi Pico inside the GameCube for use with the PicoBoot project. This allows you to have a cleaner, adhesive free install while retaining easy access to the USB port. ...Requires 2 M2x3 screws.&nbsp;</p>

This model is designed for Raspberry PI 3 and RPI GSM ADD-on V2.3 and old.

Mini gamecube case for the Atomic Pi board. Parts list as follows, i did not use a micro sd card. I used this case for a Batocera install and used the usb to sata adapter a long with a 1TB 2.5" Hard Drive. If wanting to preserve the USB 3.0...

AoT Regiment emblems case for the raspberry pi 4

This is meant to just hold a Raspberry Pi on the printer (for OctoPrint etc). It fits flush to the profile of the raspberry Pi, and elevates the pi around 10mm off of the rail. ... NOTE: if you mount it vertically, you will need a piece of tape...

Clip on holder for a Raspberry Pi for the Predator clips securely around the pillar and into the screw holes prints without supports, allows access to the power and other connections on the side of the Raspberry sized for a 29mm case -...

Based on the Raspberry Pi Case 2 I designed some Snapper for the Case and positioner for the holes of the RaspberryPi so the Print gets more fixed within the case.

Case for Raspberry Pi 4 on a Prusa MK3 / MK3s frame using M3 bolts. Includes space for heatsink and 40mm fan. ...I use this Noctua: https://www.amazon.com/gp/product/B07DXS86G7

Ender 3 Raspberry PI Mounting Case, No Hardware Top mount. ... This is my first remix/design.

Stand for the Picoboot mod (Raspberry Pico on Gamecube) with a slot for a M2 insert on the left and a pin on the right.You obviously need an insert for a M2 screw (as seen on the picture of the stand alone) and a M2 screw.UPDATE: I added a version...

Clip-on Raspberry Pi camera adjustable arm and camera case. The base is attached to a binder clip and can be attached to the bed and easy to re-position. ...Compatible with following Raspberry Pi base and camera case by barneyj:...

I wanted to put my Raspberry Pi 2 near the Mini-USB Port on my Ender 3 printer and use my existing case. So I created a holder for the case, that i can screw it on the 4040 rails. ... In the bottom is a big hole, so that the Pi can get fresh air :-)...

Clipp on harddrive cage for Malolo's raspberry pi case. The cage clipps into the bottom of the bottom_mesh_sm part from the original case and fits normal 2,5" drives. ... Here's a link to the original case: https://www.thingiverse.com/thing:3723561 I...

Made a simple mount for a Raspberry Pi case (not the case it self) on my Ultimaker 2. Glued the case to the "hanger" w/ superglue. Used support and 0.1 mm layers. ... The case I used: http://www.thingiverse.com/thing:665042 ...

# Raspberry Pi Power Splitter Case Add-on # Summary This thing is an add-on case for the Raspberry PI Case linked below. When working with this case and the Raspberry Pi, I found that I needed more 5V and 3v3 Source pins and so I decided to add a...