gum case 3d models
205041 3d models found related to gum case.thingiverse
This is a lightweight, thin, gum case or sleeve to protect gum boxes from being destroyed in your backpack, car, etc.
thingiverse
Intro The goal of this project was to make a gum case to prevent the crushing of gum in transit. The gum case also needed to be one handed. I have been using this personally for around 3 months but have now just gotten around to releasing it. What...
prusaprinters
This is a lightweight, thin, gum case or sleeve to protect gum boxes from being destroyed in your backpack, car, etc. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.20 Infill: 10 Filament: TECBEARS...
cults3d
Intro The goal of this project was to make a gum case to prevent the crushing of gum in transit. The gum case also needed to be one handed. I have been using this personally for around 3 months but have now just gotten around to releasing it. What...
thingiverse
This is a case for trident gum. ...Putting the gum pack in this case will prevent it from falling apart.
thingiverse
Quitting smoking? ...Tired of having your nicotine gum messed up in your pocket? ...Try this case.
thingiverse
Small case to hold loose packs of Nicorette Chewing gum. ... I cut out sections inside to use less material and speed the print V3 has a cut in the bottom to push the gum up and out.
thingiverse
This low profile case fits the standard 14 piece Orbit gum pack and will keep your gum safe and protected for weeks, months, or possibly even years in even the most tumultuous of pockets or purses*! ... *These claims have not been verified and are...
thingiverse
It's a snug fit for a standard case of extra gum and it's dog durable. FYI: XYLITOL IS POISONOUS TO DOGS. If you have a dog, please be very careful about what sorts of chewing gum and candy you keep in your house. Xylitol is a relatively common...
thingiverse
This little case holds 5x Nicorette Gums neatly with a click open top, the hinge is just a piece of 1.75mm filament Printed without support, use a lighter or match to just heat up the filament at each end of the hinge and press a little to keep it in...
thingiverse
This is box for rigs from feeder gum. ... You need 2 neodymium cylinder magnets 3x3mm and 6 nails 1,25x16mm https://youtu.be/-edtNaeT6aM
prusaprinters
A quick way to reuse the mentos chewing gum case to hold things on the Ikea Skadis pegboard.The clip makes it quick and easy to remove the case when you need but it also holds the case firmly to the pegboard.Print instructionsFilament used: DAS...
prusaprinters
Much studier than the typical disposable paper-backs but small enough to fit efficently in your pocket.Remixed this Print-in-Place gum case to eliminate the need for magnets. Holds up to 5 standard pieces securely. ...Example shown uses 5 Brand...
thingiverse
It is a case to carry gum https://www.youtube.com/watch?v=RL-A7H6_4Ac
thingiverse
This case fits eight cubes of gum so you don't have to lug around the bottle. ...The cap snaps on.
thingiverse
insole that holds 9 pieces of gum without coming off The brand of gum used is Clorets. ...
thingiverse
The GumPod is a rigid hard case designed to hold even your most delicate of gums. It uses a 6x2 cylindrical magnet to keep the case closed tight until you need it and for ease of use when opening and closing. The magnets have a tight fit so they...
cults3d
It is a candy case that can easily take out candy and eat it. ... assembly order 1. Outer case + Inner case 2. 1+pillar 3. ...2+cap ** All you need is M&M, Except for the printed parts.
thingiverse
Hey Trident White addicts! Want to carry around you gu in your pocket without looking like you're carrying cigarettes???? Then print this! I was furious when Trident switched to a pocket-unfriendly-version-2-pack of their Trident White series...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: $fn = 32 FOR_PRINT = 1 diametral_pitch = 0.6 ro_PLA = 924 GENERATE_PULLEY = 1 midGearAngle = -5 epsilonCSG = 0.1 gear_hold_R = 4 baseFrequC0 =...