hpi firestorm 10t parts 3d models

These are the essential mounting holes for the Firestorm 10t radio-controlled car ( http://www.hpiracing.com/kitinfo/105865/ ) to mount the transmission, gearbox brace, suspension and steering linkage/servo. This does not include the motor mount...

The brace for my older Firestorm was broken and I couldn't get a spare. ...So I re-engineered it.

The hex was buggered on one of the wheels on my HPI Firestorm Flux and the spare set was taking ages to arrive, so I had a tinker on tinkercad and designed one to use in the meantime. I printed it at 0.2 with 25% infill and it held up fine on it's...

HPI Firestorm Batteriehalter GoPro Mount Print Settings Printer: All Rafts: No Supports: No Resolution: 0.1 - 0.3 Infill: min. ...35% Notes: Perimeters 2-3

This is the front plastic cover for the front arm pivot pins on the HPI Firestorm. It is just a cap which stops the pin pivot which joins the wheel arm to the body coming out. The original is one piece, this replacement is separated so you can just...

HPI's thumbscrews are fiddly, expensive and easy to lose. Combining this adapter with an M3 nut gives you a cheap, replaceable and more ergonomic way of securing the battery. ...Depending on your print settings you may need to use a vice or other...

This is a printable replacement for the HPI E-Firestorm and Firestorm Servo Saver.You can use it with the original HPI parts like the spring, metal sleeve and nut.It was designed due to the spare parts shortage for HPI models. I printed it in...

some aluminium parts of hpi savage in.igs

... they don't get in the belt. Parts are likely able to fit other HPI vehicles, I found the lower control arms for my Rally appear to be close enough to the standard RS4 that the ones from this page will work: https://www.thingiverse.com/thing:4655433

Made a batteryplate for my friends car. It will fit for a 5000mah 3s 30c battery. ...Print Settings Printer: Da Vinci 1.0A e3d v6 repetier ...

The brace that sits between my wheelie bar broke, so I made a replacement to the exact same size. It prints in no time and has held up perfectly so far! I have modified/improved the design slightly since printing the one I am using on my...

X - SIZE 8.7 !!!!!!!!!!!!!!!!! ...Front and Rear Bumpers and Simulated Front Off Road Lights (Part # 85059 Partial)

A fully animated Firestorm skill used by the Wizard class in Hartland Tales!

brace and doodads for attaching and spacing, included the fusion file so you can mill it if yu want

A true titan of the battlefield, the firestorm has a weapon for every situation, every threat, from slaying towering titans to clearing infantry for your advancing troops. Truly the firestorm is sure to sweep its way through your enemies 28mm model...

... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40704 Instructions Using the following options: font_size = 12 ring_size = 20.17 message = FireStorm ring_thickness = 1.6 ring_width = 8 Font = write/Letters.dxf font_spacing = 10

Small model of the shardblade Firestorm from the Stormlight Archive by Brandon Sanderson. The sword is modeled on the image drawn in Book 2. Print two copies of the main blade and one connector, and glue the blade together, using the connector to...

http://www.thingiverse.com/apps/customizer/run?thing_id=45424 Instructions Using the following options: edge = 5 radius = 15 Font = write/orbitron.dxf tagThickness = 10 tagH = 20 textT = 5 width = 50 line2 = FIRESTORM line1 = HONDA holeRad = 5...

The Shardblade Firestorm from Brandon Sanderson's Stormlight Archive. This is a modified model which has been scaled to be 1:2 of a life size Shardblade and can use 4mm dowel to help hold the model together. This is only half the blade, so print it...

My FireStorm is a great kit, but the small wheels make it difficult to land in grass. I designed these wheels to replace those. They are a little heavier, but the model can easily handle the weight and it helps by adding a little more nose weight...

Bonjour, Voici la bague de retenu du ressort amortisseur HPI SAVAGE. Pièce de remplacement pour dépannage. ...

https://alexandridk.wordpress.com/titanium-tvp-wheelbase/ I tested many 3d printed parts it's fine, recommended use Nylon, PETG, TPU for different parts. Use as you see fit. ... https://www.youtube.com/watch?v=3ql-92WRdG8 ...

https://www.youtube.com/watch?v=q1DtarSJld8

hoist capacity : 10t

Benne 10T Adaptable

Customized version of https://www.thingiverse.com/thing:2572111 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2572111

Customized version of http://www.thingiverse.com/thing:525490 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=525490 Instructions Using the following options: r = 10...

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627