icom 2730a mount 3d models
348327 3d models found related to icom 2730a mount.thingiverse
I designed this 2 piece mount for the Icom 2730A to be able to mount the faceplate remotely. I used it in my vehicle but it could just as easily be used on a desk or anywhere. There is a stand to be secured where ever you want the faceplate mounted...
thingiverse
I took the Size B (1 inch) Ram Mount ball From Ozy's mount and put it on aomitri's ICOM 2730a faceplate mount. ... RESULT: IC-2730a faceplate mount w/ Size B (1") Ram Mount ball.
thingiverse
Bracket to mount the Icom 2730A onto my desk. Desktop thickness is about 16mm. There are 4 parts to this design. -The base, which is ziptied to a bar underneath the desk. -The arm, lifts the faceplate up and angles it. -The backplate, which...
grabcad
A suitable stand in for the HAM radio made by ICOM. ...I used this to create my 3D printed mounting brackets.
thingiverse
the back hole has a common thread of 1/4 the same that is used in the photographic screws and tripods Soporte de pantalla para la base icom 2730a. ... el agujero de atras tiene una rosca comun de 1/4 la misma que se usa en los tornillos de fotografia y...
thingiverse
ICOM 2730A faceplate bracket to stay on top of my monitor. The monitor is the LG 24M37H-B. You can also add a thin strip of double sided tape on the back to prevent shifting. ... It fit's tight on mine, so I don't need any.
thingiverse
I lost the magnets for my Icom ID-5100a head unit and decided to whip up a really quick mount to attach the faceplate to my wall with two drywall screws. ... Its not pretty but it works!
thingiverse
Mount for Icom ID-4100. v1 - It works so unless I find some flaws as I use it I don't suspect I'll revise it. There is about 1mm gap from the radio on each side. Using 4 m4x8 screws I was able to cleanly attach the radio. There are 4 mounting...
thingiverse
I found this mount listed for the IC-2730a (https://www.thingiverse.com/thing:4879947) and shaved the base in Tinkercad. I have both the IC2730a and the ID-5100a and can confirm it fits both radios. It may fit others that take the MBA-2 or MBA-5...
prusaprinters
I found this mount listed for the IC-2730a (https://www.thingiverse.com/thing:4879947) and shaved the base in Tinkercad. I have both the IC2730a and the ID-5100a and can confirm it fits both radios. It may fit others that take the MBA-2 or MBA-5...
thingiverse
Cradle mount for ICOM HM-234 microphone, for use with clip that comes fitted to the mic. ...(This is the microphone supplied with the IC-705.)
thingiverse
Magnetic mount for Icom HM 207s. I designed this so that I could mount my mic on the roof console of my truck. Some sanding is required to make it seat deep enough in the mic. When tightening the screw, remember it is plastic. I printed with...
thingiverse
This is a RAM Mount compatible holder for an iCOM ID-51. It will fit the larger battery as well as the stock battery. I used M4X25's to put it together. There is a tiny amount of space for thin rubber cushion to keep it from rattling. If it will stay...
thingiverse
This is a RAM Mount compatible mounting plate for the iCOM IC-7100 head unit. It requires a 1" RAM ball adapter and what ever RAM arm mount you need to mount it. It also requires 3 screws to attach it to the plate. I used long computer hard drive...
thingiverse
ICOM is nice, but the proprietary mounting method isn't fantastic. As such, here is a bracket which will accommodate your own ideas and designs or to completment/replace the original. If used in a vehicle use PETG/ABS or another temperature...
thingiverse
Icom Ic7000 with the LDG AT7000 tuner these brackets marry them together to make them one unit for easy use in the car and home alike, hope it helps you out I printed it in PLA using 0.14 standard speed 35& infill, Just open in cura and mirror to get...
thingiverse
I was looking for a cheaper alternative to the IC-7100 Mount for the truck... It turned into this. Works pretty well. Made of PETG. Enjoy! Please don't sell it. ...I'm doing that already.
thingiverse
Screws to mount the Pi are 2.5mm x 16mm and screw directly into the holes without drilling and tapping. Pins for locks are super glued into the lock blocks with very little glue and its important to keep the the lock blocks moving until the glue...
thingiverse
Needed a solution to mount an ICOM 2730a head unit in our 2021 Ford Bronco. Tweaked these components and came up with this 3 piece adjustable mount. ... GoPro Screws: https://www.amazon.com/gp/product/B074K9ZFG2 Icom Head Unit thumb Screws:...
thingiverse
ICOM IC-E80D handi wall mount. I will make one with a stand shortly. ...Will also put one in my van.
thingiverse
Simple desktop holder for control panel to Icom IC2730. ...
thingiverse
I mounted the head unit onto a Lido mount. ICOM doesn't make anything for the that so I did. This is uses a counterbored bolt in the center for the Lido mount. ... http://www.lidomounts.com/homepage.html ...
thingiverse
ICOM 2730 Faceplate Bracket to 20mm RAM mount. This eliminates the need for ICOM MBA-5 ($40) and 20mm RAM/AMPS plate ($15) Designed in Auto CAD Sliced using Cura Printed successfully on Ender-3 100% infill PLA 220deg / 55deg bed Requires 2x M2.6 x...
thingiverse
This is a Mount to place the Leo Bodnar 10MHz reference mini GPS module on the side of the ICOM IC-9700 radio. ... This uses 2x M4x8mm screws (MAX 8mm, or you will damage the radio) I printed this side on, with supports on build plate only, 0.2mm,...
thingiverse
https://www.thingiverse.com/thing:3569530/ Remixed the VESA mount to work with the faceplate of an Icom 5100 radio. This mount will work with the Articulating Arm here: https://www.thingiverse.com/thing:2448971 Shown in pictures with the VESA mount...
thingiverse
This is a quick and dirty mount i created for my icom ic-7000 in order to attach a vhf-uhf handheld antenna to it. When the radio is used on an table with the fron feet extended you can not use an angled connector to mount a small antenna for v/u...
thingiverse
This mount has holes to screw to the faceplate and then tabs to slide into the body of the radio in the same way the Icom one does. You will need 2 M2.6x5mm screws. The face sits centered on the body and flush with the bottom of it. Could be laid on...
thingiverse
I simply added a front support with mounting holes to hold the metal baseplate for the Icom ID-5100 transceiver. The addition is a little rough around the edges, but, it works fine and isn't seen when the draw is in position. The draw space is...
thingiverse
I had an old cellphone mount still in my truck - and thought a printed baseplate could turn it into a great place to mount my ID-800H's tuning head. Instructions I printed this with PLA and 25%...