keltec cp33 accessories 3d models
40055 3d models found related to keltec cp33 accessories.thingiverse
CP33 Configuration Keltec CP33 Forward Angled Grip, #4677465 by Todd Gomez, Likestoshootstuff https://www.thingiverse.com/thing:4677465 CP33 magazine baseplate, #3980528 by Feral Daryl, feral_daryl https://www.thingiverse.com/thing:3980528 REHV ARMS...
thingiverse
CP33 Configuration: Keltec CP33 Forward Angled Grip, #4677465 by Todd Gomez, Likestoshootstuff https://www.thingiverse.com/thing:4677465 CP33 magazine baseplate, #3980528 by Feral Daryl, feral_daryl https://www.thingiverse.com/thing:3980528 REHV...
thingiverse
I found it annoying to remove the mag from my CP33 because there just isn't much real estate to get a hold of. This baseplate is wider than the factory one, especially at the front, allowing you to get two fingers on the mag and your thumb on the...
thingiverse
These are magazine cases primarily intended for KelTec CP33 22LR magazines. They can be used for other magazines of similar size and design or for other functions. Resize as necessary. Four (4) sizes are available: 1) single 2) double 3) triple,...
thingiverse
This is a remix for an angled grip with a steeper angle, and no rests or rails on the side. ...this is a forward angled grip, it is not intended as a vertical foregrip, it even says so on the side.
thingiverse
kel-tek cp33 short and long rails i split them to print and super glue together
thingiverse
I made a Magpul-style baseplate for my KelTec CP33 magazine. I used part of martialmedia's design and adapted it to fit my application. ... https://www.thingiverse.com/thing:1443089
thingiverse
Especially with KelTec devices. This wrench will help you to screw the thread protecting nut without damaging its finish. Warning - use on cold barrel only! It is better to print this with nylon or something strong. But it will work with PLA on...
thingiverse
This is an adapter for the keltec cp33 to use a tailhook arm brace. hardware youll need: the acutal ATF approved tailhook 10mm alumium rods or feel free to made that smaller for whatever rods youwant to use. ... 2small screws 2mm x 8mm for the back...
thingiverse
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. ...It should function just as well as the proprietary version.
thingiverse
(this model has not been printed and tested) - CP33 Shroud mlok no rail - This model does not include the area for the igitalnimbuslabs brace rails. If you dont need that attachment then this is the model for you.(this model has not been printed and...
thingiverse
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. ...This is the same as my previous magazine extension, but it has no grooves as...
thingiverse
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. This is the second version. ...It is slimmer, fits better, and has a stronger lip...
thingiverse
A design for a replacement buttstock for a keltec sub2000 gen2. please try and give feedback. ...thanks!
cults3d
This was originally as a mount for a Bushnell Trophy TRS-25 Red Dot sight to fit on a KetTec CP33 with the original iron sights still usable. It mounts to the picatinny rail, and has one picatinny slot in the middle of the top for the red dot to...
thingiverse
Shroud replaces stock mlok barrel shroud on the CP33. Use stock screws to mount the shroud. The print still provides a mlok slot in the same location. Light compatibility designed for Streamlight TLR RM 2. Pressure pad half installed with shroud...
prusaprinters
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. This is the second version. It is slimmer, fits better, and has a stronger lip...
thingiverse
This is a grip plug for the Keltec RDB. It allows you to store small items such as a bore snake or other items in the grip. ... -EDIT 11/13/2019 Added low profile variant
thingiverse
Quick and dirty side rail for the Keltec RDB. You'll need to use longer screws for this since the stock ones are too short, M3x20 work best. Included are left and right side rails which allow access to the takedown pin, and a stronger universal model...
thingiverse
Quick and dirty side rail for the Keltec RDB. You'll need to use longer screws for this since the stock ones are too short, M3x20 work best. Included are left and right side rails which allow access to the takedown pin, and a stronger universal model...
thingiverse
Simple stick on shell deflector for the KelTec Sub2000. Offers a bit of protection for those of us who are left-handed. Used 3M double sided automotive mounting tape to attach it. The fit is not quite right, although it looks pretty good. I may...
thingiverse
angled forgrip for keltec cp33 with thumb rest and rail left and right
thingiverse
Gentlemen, I decided to work on some Kel Tec CP33 accessories and this is the first piece, its a P-Rail brace adaptor, I designed 4 versions starting from large and all the way to micro. You will only require 2x M3 x 20mm socket head screws to mount...
thingiverse
Harware needed: 1 - M4 x 35mm bolt (Found at lowes or homedepot in packs) 1 - M4 Nut (Found at lowes or homedepot in packs) Original hardware for the stock mlok barrel shroud, it should be 2 screws Any other hardware to mount an mlok attachment...
thingiverse
Pistol grip Plug for KelTec RDB. ...Turn your pistol grip into compartment
thingiverse
Voici un levier de chargement à deux doigts pour la Keltec Sub2000. Mon levier d'origine ayant cassé, j'en ai usiné un nouveau dans une barre de 8 mm de diamètre. (ici une tige de vérin pneumatique. On pourrait prendre une queue de forêt, un bout de...
thingiverse
This is a replacement floorplate/baseplate for the Keltec PF9 magazine. Update: Added baseplate with fingergrip extension. File v3 Print Settings Printer Brand: Wanhao ...
thingiverse
Print in flexible filament. ...This will allow for you to mount a Hatori Super Small Mini LED Flashlight at an ultra-low profile on the top picatinny rail of the Keltec cp33, so that it is adjacent to the right side.