kobalt 24v router 3d models

Kobalt 24v Max Lithium Ion battery model

Designed for my shop as no other battery holders were out there for the Kobalt 24V.

This is a little something I whipped up to hang my 24v Kobalt tools from the underside of a bench, or in my case some cabinets.

... Batteries. ...It complements my design for a tool holder for 24v Kobalt tools. It will mount your tools and batteries under a cabinet or bench. This is optimized to print without supports. Simply print upright with the word battery facing up. ...

A simple rack for storing Kobalt 24V Max batteries. ...This was specifically designed to fit the 4 amp packs but would also fit some smaller batteries without modification or any others by scaling the model as needed.

i designed a handle for my kobalt 24v weedeater that is slimmer and more ergonomic than the stock handle. ...i used a layer of electrical tape inbetween the handle clamp and the weedeater shaft.

Kobalt 24v battery to Ryobi adapter. https://www.lowes.com/pd/Kobalt-24-Volt-1-5-Amp-Hours-Lithium-Power-Tool-Battery/1000090833 WARNING! Ryobi tools may not handle 24v. use at your own risk. https://www.youtube.com/watch?v=0vb_w2qyKcg I used this on...

Designed and printed wall mounts for various Kobalt 24v tools. Reciprocating Saw (requires supports) Oscillating saw and Hand Light Impacts and Impact Driver Skill Saw High Speed Drill Battery Mounts The spacer was designed to evenly space...

Made this nozzle for my Kobalt 24v Blower. It does restrict the nozzle, but not sure if I will continue to run it or remake it and open up the end a little more. ...It snaps into place on the end of the tube and will not blow off, may be a little...

Made a quick battery holder for my extra Kobalt batteries. ...Enjoy

Three piece project box for Kobalt 24v batteries. I use 1/4" x 18 gauge copper strips, bent to an "L" shape for the contacts.

Simple wall mount for a Kobalt 24v battery. ... Recommend printing it standing up so that the print layers are perpendicular to the base for strength holding the battery, and I've been able to print without supports.

Remix from Stealthy_TT Kobalt MAX 24V battery under shelf mount made it into a wall mount can still be used for under shelf. Just Rotate 90 degree like in the picture. ... You are not allowed to sell this its only for personal use.

Kobalt Router Table Ring was a replacement for the missing piece of my router table. ... You may have to do some fine tuning for this item to fix snuggly in.

Replacement router table inserts for the Kobalt Router Table. They fit better than the originals. About one hour print time per insert. Printed at .2 layer height and 50% fill. Center hole sizes match the OEM inserts: Small 1-1/4" center hole Med...

I needed a zero tolerance insert for my kobalt 24v miter saw. ...designed in sketchup with .skp included for any modifications.

bump feed for Kobalt 24v string trimmer. So far it is holding up very well, printed this last yr. ...I suggest printing at 100% infill.

Kobalt 24v battery to Makita adapter. Warning! Makita tools may catch fire or explode when 24v is applied. use at your own risk! ...extremely experimental stage, may not function at all.

Just a simple under shelf mount for holding up Kobalts line of 24v batteries This will not work as a wall mount, my mistake. ...If you do need a wall mount i can adjust it and post a new thing for it.

This is a tool holder mount for the Kobalt 24v Max line of tools. The tool holder definitely works for the drill, impact driver, and circular saw, and probably others with similiar dimensions. I will be designing further refined versions for the...

I wanted the airflow of my 24v Kobalt leaf blower to have a wider output and angled slightly so I designed this. The thickness is only 0.8mm so that it will flex and doesn't break as easily and as a bonus doesn't use much filament and quicker to...

I wanted the airflow of my 24v Kobalt leaf blower to have a wider output and angled slightly so I designed this. The thickness is only 0.8mm so that it will flex and doesn't break as easily and as a bonus doesn't use much filament and quicker to...

I wanted to hang my Kobalt 24 volt hand tools from the underside of my shelf, so I built these a few months back. The current STL's are my third version, and allow for countersunk screws, no supports required, & prints in just around an hour for each...

Push block for the Kobalt router table. The included push block was quite loose in the track and this is a nice tight fit (on mine at least). ...I also made a positive and negative 15 degree block since I seem to use those angles quite a bit in...

I printed Rick's 24v battery mount and then remembered that my wall is all pegboard and it would be best to be able to move my mounts around as my tool collection changed. So I added pegboard hooks to his original design, but then also created a...

This is a first attempt at making a tool holder for the Kobalt Router table. It is printed in two parts to avoid using supports. The pieces will be bonded with glue. This holds two inserts, the 1/2" collet, the starting pin, wrench, and lift allen...

This is a nozzle for the Kobalt KHB 2024B-03 24V leaf blower. This one is specifically for the -03 newer model number blower. It has recesses that allow the nozzle to twist-lock onto the two tabs on the end of the blower's barrel. Nozzles...

This plate is to be used when the router is attached to the router table. ...It allows the router tables dust collection port on the fence to function as intended as well as allows the use of the height adjustment key.

The knobs to adjust the fence on my router table were difficult to get to so I made these knob extensions that are a lot easier on my hands. I included built in supports so no slicer generated supports are necessary. ... Printed in PETG so it won't...

The knobs to adjust the fence on my router table were difficult to get to so I made these knob extensions that are a lot easier on my hands. I included built in supports so no slicer generated supports are necessary. ... Printed in PETG so it...