langmuir crossfire 3d models

This is a collection of upgrade parts I designed for my Langmuir Crossfire CNC plasma table: - Strain relief anchor for Y axis motor cable - Strain relief anchor for plasma torch and Z axis motor/switch cables

These are mount brackets for attaching momentary contact switches (e.g. ...https://smile.amazon.com/gp/product/B00MFRMFS6/) to the beams of a Langmuir Crossfire Plasma CNC.

Water shield for the Langmuir Crossfire Pro plasma table. This slides onto the bottom of the Z-axis to prevent water from splashing up onto it. It is a tight slip fit and should stay in place without any fasteners. I designed it to fit around my...

I just got my Langmuir Crossfire XR setup and started to use it when I decided a laser alignment tool would speed me up when setting up my cuts. I looked around, but only found prints for the Crossfire Pro. After some thought here is what I came up...

This sharpie holder is set up to clamp into the torch holder on the Langmuir Crossfire plasma table. Post process just the outline of project and see where the cuts are going to be. I printed one and it works perfectly! The cap and body are...

This cover is a tight slip fit over the bottom of the Z axis on a Langmuir Crossfire plasma table with a powered Z axis. It protects the Z axis rails and IHS switch from splashing water. This cover will only work with a Machine torch. There is no...

laser crosshair for Langmuir crossfire pro cnc plasma cutter

This piece is designed to fit on the lip of the Crossfire Pro water table and hold a bilge pump hose in place for refilling the water table from a storage tank. This is a great way to easily avoid water level loss by evaporation. ... More info on the...

Simple machine torch mount for Langmuir Crossfire plasma tables with Z-axis. This mounts to the table with 2 - 1/4-20 socket head cap screws through the existing threaded holes in the Z-axis carriage. The clamp is designed to use M5 x 25mm...

These are the dimple dies I made to install my 1.5" drains on the crossfire pro table. Use extra large washers (3.5"- 4") to back both dies and lubricate the to aid in forming. The step in the die is more of a stopper. Obviously the stainless is...

Print with 3-5 shells and 50-80% infill. ... Requires 4 x M3 Screws 10-14mm long.

This the drain nut backer to allow a good fit between the drain nut and table. ...(so the nut doesn't just tighten on the low spot created by the dimple die.

Langmuir Probe Holder: http://wp.me/plWJv-NY

This is a solution for mounting the torch height control box for Langmuir CNC tables. It has tight tolerance and holds the box into place with friction. Designed to mount with #10 countersink screws. ...

This is a touch probe holster for the Langmuir mr1, allowing you to leave the probe cable hooked up at all times. Most of the strength is going to come from the wall thickness rather then the infill. You can keep the part lighter by increase walls...

The objective for our final project was to collaborate with a faculty or staff member in order to design and print a 3D object that could be used to promote a topic of interest. Since I am a strong supporter of chemistry research, I decided to...

Holder for the toe clamp kit that comes with the Langmuir MR-1 CNC mill.

AN94 in Crossfire for Chinese Crossfire Wiki.

модель сцены карты Crossfire

The map Brakeout crossfire

ES UN DISEÑO QUE ACOPLA LA ANTENA DE CROSSFIRE AL QUAD

SummaryHere are the (very) long overdue Crossfire and Crossfire 2 Arms and accessories. All the arms are compatible between both platforms and address most of the issues people have had in previous versions. Both the original Crossfire and...

https://vimeo.com/79370836 Fpvlab.com Thread:http://fpvlab.com/forums/showthread.php?25717-3D-Printed-Crossfire-2&p=433303#post433303 So what is new with the Crossfire 2? In general, a lot! It looks like the same ol' Crossfire but its not. I took...

Both the original Crossfire and Crossfire 2 arms are included along with the 3.0 arms. The 3.0 arms are basically a modular version of the previous arm. Using the arm without any legs attached is perfect for using with Skids attached. The arms...

https://vimeo.com/79370836 Fpvlab.com Thread: http://fpvlab.com/forums/showthread.php?25717-3D-Printed-Crossfire-2&p=433303#post433303 So what is new with the Crossfire 2? In general, a lot! It looks like the same ol' Crossfire but its not. I...

The Crossfire is supposed to fly up to 350 meters on a c6-5, in reality it only flies up to around 255 meters. The 3d printed version is a mono body design, meaning that the fins, motor mount, launch lug, and the body tube are all one piece. When...

SummaryHere is a pair of skids designed for the Crossfire or Crossfire 2. They attach to the bottom plate via M3 hex screws and can be used instead of the legs integrated into the arms. I have tested it up to a three foot drop at gross weight. The...

Here is a pair of skids designed for the Crossfire or Crossfire 2. They attach to the bottom plate via M3 hex screws and can be used instead of the legs integrated into the arms. I have tested it up to a three foot drop at gross weight. The legs...

I modified the original laser bracket and elongated it with tabs to prevent the hand torch from rotating which causes misfire issues. ...It get's the job done I have done several cuts with it on

I printed this with a .28mm layer height, 3 walls and 30% infill. This snaps over the back of the Z axis, as shown in the pictures. The IHS wires have to be disconnected and fed through the slots after installation. The screw/clamp that holds the...