microsoft lifecam cinema tripod 3d models

I needed a tripod mount for MS Lifecam cinema that did not require me to remove the flexible clamp already attached. This block tripod mount has a channel that the flexible mount will fit into and allow you to mount to a tripod. ...Printed in PLA at 20%...

I use a Microsoft Lifecam camera to watch my 3D printer and wanted a tripod mount for it. The bottom has a threaded 1/4-20 hole so it fits an ordinary tripod. To clamp the camera in place you need a M3x12 bolt and washer. I printed this in PETG so...

I use a Microsoft Lifecam camera to watch my 3D printer and wanted a tripod mount for it. The bottom has a threaded 1/4-20 hole so it fits an ordinary tripod. To clamp the camera in place you need a M3x12 bolt and washer. I printed this in PETG so it...

... Cinema WebCam. ...This does not fit other webcams in this series like LifeCam Studio or LifeCam HD-3000. Example of Webcam can be found here: https://www.amazon.com/Microsoft-LifeCam-Cinema-Webcam-Business/dp/B004ABQAFO/ref=psdc_172456_t1_B0096KSBB0

... Cinema y poder mantener nuestra privacidad. ...Para porder usar, solo tenemos que levantar la tapa. Useful to cover the Microsoft Lifecam Cinema webcam and to be able to maintain our privacy. ...To be able to use it, we just have to lift the cover.

Cover for the Microsoft LiveCam Printed with PLA 10% infill. ... I used a small nail to combine both parts.

This litle widget clips into the base of my Microsoft LifeCam VX-6000 and allows me to screw it onto a tripod with a 1/4 in thread.

This is a gimbal designed excluisively for Microsoft LifeCam Cinema webcam. It uses two popular TowerPro SG90 9G micro servos. Servo arms are glued to the print with epoxy.To complete this project you also need 35x10 screw with nut. ... For electronics...

A tripod for said webcam consisting of 4 pieces

I have a Microsoft Lifecam Cinema which has a far better resolution than the standard raspberry pi camera, so I just whipped up this to allow me to use it with the articulating raspberry pi camera system. Please refer to the "Articulating...

A simple lens cap for the Microsoft webcamera used with the Makerbot 3D Scanner designed in OpenSAD quite literally in seconds. NOTE: Parts of this file lie below z=0, this file needs to be moved onto the platform before printing! Be careful if you...

All the other tripods for the Microsoft Lifecams out there needed screws or modifications, so I appreciate this simple design that brings it up just high enough to use for Octoprint webcam monitoring or however you monitor your 3d prints. Be warned...

... inch Tapping Task. ... This Tripod is Joby GorillaPod Micro 250 Add 12/24/2015 camera stand, camera stand angle, camera stand straight, camera stand joint. Add 01/15/2017 lifecam_magnet1,2,3 and lifecam_angle_lock. ...Add 03/04/2017 lifecam holder.stl

This is bracket for Microsoft LifeCam Cinema mounted on 3030 aluminum extruded profile.

Tripod Mount Hole 5mm -> W1/4 inch Tapping Task. ...This Tripod is Joby GorillaPod Micro 250

This is bracket for Microsoft LifeCam Cinema mounted on 3030 aluminum extruded profile. Print instructionsSupports: Yes Resolution: 0.3 Infill: 40% Filament: Prusament PETG black

LifeCam Cinema Webcam for Aluprofil gyroscopic 360 2x M3x20 2x nuts T-Track Sliding Hammer ( Amazon.com )

A simple camera holder for the Microsoft Lifecam Cinema. I found that the tiny screw holding on the standard mount was way too weak to keep the camera secure, so I remixed this from the camera mount I used on my old Wanhao i3. The camera is held...

Simple tripod mount for Microsoft Lifecam, because I always hated the flexible stand it came with.

handy tripod support for MICROSOFT LIFECAM HD-3000 Better version remixed by dmarc73 herehttps://www.thingiverse.com/thing:2917065 Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: Yes Notes: the hole do not have the...

... the hole. If it's too loose, try adding some super glue on the outside of the nut to hold it in.Check the original for instructions on how to properly disassemble the Lifecam to remove the stand and fit it on the mount.  Category: Camera

Modded the original so it could be mounted to a tripod. ...This is currently being used to stream video of a robot to programmers located off-site.

Kameraabdeckung / Camera cover - Microsoft LifeCam Cinema WebCam for Business Verdeckt die Linse und das Mikrofon ------------- Conceals the lens and microphone

Modification of a Microsoft Lifecam Cinema Webcam to an 1.25" Astro Camera. For disassembly, visit http://dslrmodifications.com/lifecam/lifecam1.html Just push gently the camera in to the cylinder. Add a foam disc to cover the blue light and push the...

Modification of a Microsoft Lifecam Cinema Webcam to an 1.25" Astro Camera. For disassembly, visit http://dslrmodifications.com/lifecam/lifecam1.html Just push gently the camera in to the cylinder. Add a foam disc to cover the blue light and push the...

This is a Microsoft Lifecam Cinema mount for the Anycubic i3 Mega. ... I used and modified parts of the following projects: This one for the base mount https://www.thingiverse.com/thing:2205804 This one for the z-axe clamp...

Geeetech Rostock 301 Microsoft LifeCam Cinema Camera Mount Mount on the left side of the printer. You will need a 20 mm Od x 1.75 mm o-ring that fit between the camera and the support.Use the original small o-ring from the camera mount for...

This is a mount to attach an old webcam I had (Microsoft LifeCam Cinema HD) to my Ender 3 S1 Pro. It mounts the camera at the rear of the printer looking towards the front which gives it a better view of the nozzle as the front is blocked by the...

A simple adatpter to put a Microsoft Life Cam Cinema webcam on top of a light stand with a 1/4 inch spigot.

PLA 0.2mm, 30%infill.