mini quad club 3d models

have fun

45 Degree Xaiomi Yi Camera mount for the MQC Fusion.

45 Degree Xaiomi Yi Camera mount for the MQC Fusion.

Frame mini quad for 7mmx20mm engines 4mm carbon tubes The wire passes through the motor inside the carbon tube I hope you enjoy

This mini quad format 130, chassis in stl and dxf version. ... Video: https://youtu.be/VCqCdpjaP7Q The main chassis is 33% PLA The hull is 20% TPU

Mini quad frame in openscad, a couple of parameters you can set for motor body diameter and prop length to auto adjust spacing. ... To do - create battery plate

Ce mini quad format 130, châssis en version stl et dxf. ... Vidéo : https://youtu.be/VCqCdpjaP7Q Le châssis principal est en PLA en 33% La coque est en TPU en 20%

3D printable mini quad concept. Not tested yet. The landing gear was intended to be printed in a transparent material and the little feet in TPU for some damping. Designed for 12 x 12 mm mount spacing motors with 5030 props or similar. ... - FC...

mini Quad sized like a Hubsan printed in 0.3 u can use Hubsan Motors (8,5mm) i used this one http://www.banggood.com/Chaoli-CL-820-8_5x20mm-Coreless-Motor-for-90mm-150mm-DIY-Micro-FPV-RC-Quadcopter-Frame-p-1054803.html Hubsan FC or a 32 bit FC for...

Mini quad club XHD frame sma mount

My first prints with the KBricks systems -- The Quad Demo and Quad Demo at 2:3 scale. Getting my first successful KBricks build was more of a challenge than I expected. Some of the parts and fit are fiddly, both to print and assemble. Lessons...

A mini driver to make a kids golf club. Head size is 3" wide, 2-1/2" long, 1-3/4" deep. ... Not including the hosel.

Brushless Mini Quad

Fly Mini Quad, 30cm

Mini quad holiday ornament.

This is a mini quad! ...

Mini quad side skirt for sub 200 mm quad, 20mm tall upper and lower battery strap holes.

Remix of a Hovership arm into a Mini one-piece quad frame.

250 quad mini racer keychain. ... UPDATE 3/9/2015: I ran the STL through NetFabb to fix the models imperfections.

Quad frame for mini 130mm quad copter Motor holes are for M2 screws on a 12mm circle Flight controller holes are 30.5mm square (for ~36mm flight controllers) Use 1304 motors with 3" diameter props

To hold plastic tubes which houses the antenna on the sides of the mini quad with minimal hardware. ... Instructions .2 layers with 20 percent infills.

Here it is, the well-known H mini quad. A project I'm started but never completed. ... If there is enough interest, I will upload the Solidworks files.

My own low-profile take on a mini quad wall mount. ... I printed in M3D Tough 3D Ink Flexible Ruby but any PLA/ABS should work well.

Made these to mount all the boards I want inside of the Spank mini quad frame. I am going to reconfigure them again with a cleaner approach to clean up the wiring and weight. ... For Spank mini frame.

Remix of the Mini quad, however this is much easier to print and I have included the 280mm arms to accommodate 8x4 props. ...Video:https://www.youtube.com/watch?v=wLS-gQTVVis

Frame for mini quad. For 8mm motors. My equipment is from EX100. Supports needed.I used grid 1% density,65 deg. overhang angle. ... My designs are free and always will be,if u enjoy leave a like to motivate me :)

Motor mounts for mini quad motors (8.45mm) to be affixed to a foam glider. edit: I realized the parts were not connected on my .stl file. Sorry about that. ... I fixed it.

Motor mounts for mini quad motors (8.45mm) to be affixed to a foam glider. edit: I realized the parts were not connected on my .stl file. Sorry about that. ... I fixed it.

Print the following: Arms x4 Base x2 Top Plate x1 Mobius Dampener x1 Please link to the original art when publishing derivatives: http://untestedprototype.com/2013/09/cloneout-mini-h-quad-plans/ Instructions Setup: RCX 1804-2300 motors Whitespyquad...

Simple display stand for mini quads. Can accommodate quads with Undersung batteries and top-mounted batteries Made up of three parts; Base Stem and Mount. ... The mount is available in 3 sizes Standard Mount Suits 16mm Battery Strap Standard Mount 2...