monoprice select mini v2 bed leveling 3d models

I scaled it down to the size of Monoprice select mini's bed. When this test is done, look at each square. They should look the same, thats the most important part. If the squares's infill looks sharp and jagged, raise the bed on that corner. If the...

I really liked the simplicity of the Monoprice Select Mini Bed Level Calibration Test, but really wanted something that I was sure conformed to the magic numbers of the Z axis so I could more accurately calibrate the bed. This is actually all I use...

I was looking around for a good bed level test print and [found this one by teejschmitz](https://www.thingiverse.com/thing:2743863) which worked pretty good, though there were a few minor issues for me that made it a bit of a struggle when printing.

remixed bed level of http://www.thingiverse.com/thing:1905398

remixed bed level of http://www.thingiverse.com/thing:1905398Category: 3D Printing Tests

Wanted to use an E3d V6 on my Select Mini v2 but didn't have a good way to bring the bed up to make up the distance of the v6 from the v5. These are 10mm round with a 3.5mm hole in the center and 4mm tall, you can place them ontop of the cup washer.

Photos above and the summary below are pulled directly from Yourdrunkle's design.** This is a modification to expand the MonoPrice Select Mini's print bed depth to 230mm on the cheap. I am able to utilize a printable area of 130mm x 220mm with just...

But if you need any offset (ex: glass bed) https://www.thingiverse.com/thing:4624845 No problem with heat bed or insulation material. Printable on the Mini (2 batchs). Reusing orignal screws. You need: - Eight (8) M3 Nuts (dimensions in the design...

But if you need any offset (ex: glass bed) https://www.thingiverse.com/thing:4624845 No problem with heat bed or insulation material. Printable on the Mini (2 batchs). Reusing orignal screws. You need: - Eight (8) M3 Nuts (dimensions in the...

edited for the monoprive maker select v2

This is a z-axis spacer for the Monoprice Select Mini V2 printer when installing a 3mm thick glass print bed. This does NOT require any disassembly of the printer to install. To install, manually move your printer nozzle UP on the z-axis about 3/4".

I routed the bed wiring through the back panel of the printer, so made a cable tidy for support and stabilisation. A 10mm hole was drilled through the rear panel next to the board cooling fan and the rubber grommet refitted. I resleeved the bed...

I have been able to quickly and easily calibrate my Monoprice Select Mini with this test pattern. The outer square is .5mm tall. The next tallest square is 1mm tall. The corner and center squares are 5mm tall. The screws holding the bed of the...

... level I'm getting my bed with sliding business cards under the extruder. ...This test print hits all the parts of the print bed and lets me see how level I've tuned it in, and how good 1st layer adhesion will be. ...I usually cancel after 2-3 layers.

Prusa inspired knob for the Monoprice Mini Select, V2. The knob is designed to clear above the LED ring, and let some light through. It's small enough to clear the bed if you need to reach it while the bed is forward. The knob is easy to spin...

I couldn't find a knob for my Monoprice Select Mini 3D v2 printer that really fit like I wanted it to so I went to Tinker CAD, pulled up a gear, and turned it into a button. ... I added v2 with a rounded top and a smaller finger hole.

###This is a the thumb wheel leveling system for the Monoprice Select Mini 3D Printer. It adds thumb wheel leveling to the Monoprice Select Mini printer. Specifically Versions 1 and 2 of the printer. Please note that this mod will not work...

I thinned out a couple of the parts which should allow this to work with a glass bed. ...The original was only 1.5 mm too thick with the thicker thumbwheel

I wanted the same thing for my Select mini V-2 . This design uses both screws on each side of printer, you only need to remove the old rubber foot pad before installing the new feet. Has not been tested on the V-1 yet. ...If you have a V-1 please let me...

** Monoprice Select Mini Thumbwheel Leveling System** This is a thumb wheel leveling system I designed for the Monoprice Select Mini 3D Printer. This system is designed to be completely printable on the MP Select Mini and installed without any...

While that did look neat it made printing the part without supports a non-starter for me. My own printer with an E3D hot-end requires the zero offset version of the mount. Find more of my work at https://pcburn.com Print instructionsCategory: 3D...

filament guide for monoprice select mini v2

This is a slightly remixed version of the original under-bed wire guard for the Monoprice Select Mini. ...The joints fit a little bit better together without excessive force.

My Heated bed wire broke soon after getting my Monoprice Select Mini V2 (~3 weeks). I didn't like the design of the cable clamps for the Heated bed, so I designed my own that uses the existing unused holes above the slide. I made this for the right...

This spacer allows you to add a glass bed to the Monoprice Select Mini without having to crank the bed leveling screws down. It clips on to the right side of the Z gantry, and activates the Z endstop switch 3/32" above the factory position. Glass...

If successful it will use the carriage, heat bed and borosilicate glass from the prusa I3 for the monoprice select mini. 6/19/17: Changed a few things on the front rail after installation. Remixed bed rail mounts from...

This is a video of my repair/upgrade to the Monoprice Select Mini heated bed. I have had issues with the wires under the heated bed wearing out, getting stuck and chaffing on the belt. I decided to solve these issues by rerouting the wires externally...

Tinkercad thing Print Settings Printer: Monoprice Select Mini Rafts: No Supports: No Resolution: .175 Infill: 50 Notes: Printed with eSUN PETG Sliced with Cura 2.4 You will need to print the part on an angle as its 145mm long. ... I also printed with a...

Just trimmed the edges of Bumbumbum's Arcade1Up SwitchBracket v2 so it will fit the print bed area of the Monoprice Select Mini printer

PROJECT SUMMARY: This is a modification to expand the MonoPrice Select Mini's print bed depth to 230mm on the cheap. I am able to utilize a printable area of 130mm x 220mm with just these modifications. The price once built was approximately $60 for...