nema 6 50 3d models
457652 3d models found related to nema 6 50.youmagine
A common welder plug is a NEMA 6-50 plug. ... This cover can protect your male plug from debris or moisture.
grabcad
Modeled the plug end of my 40 amp 6-50 heavy duty extension cord with 3-8 awg conductors.Model units are inch.
thingiverse
This is designed for an industrial grade NEMA 14-50 like the Hubbell or Bryant. Inside Diameter is 2.45 inch. There are two files, one with the Tesla logo and one without. Also Cura states there are holes in the model, but it printed fine for me,...
thingiverse
... holes to prevent water accumulation as well as to allow for test leads. There is a loop for a para-cord tether so that it isn't misplaced. This was inspired by njcrawford's Cap for NEMA L14-30 plug: https://www.thingiverse.com/thing:2974604.
thingiverse
The 50 Amp outlet suggested using a 2 gang box to mount it in, but the store only had single gang style covers. So, needed a 2 gang cover. ... Fusion 360 Link: https://a360.co/2WOdKmQ
thingiverse
The other NEMA 14-50 outlet covers were not able to cover the entire metal plate of my NEMA 14-50 plug, and were showing screws. My design is bigger, and you put it in place with 4 spots of silicon glue, or hot glue. Look better. ... As always I...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_step_shape_degrees = 45 non_thread_diameter = 15 head_height = 5 outer_diameter = 14 socket_depth = 3.5 texture = include type = rod...
cults3d
This pack contains 50 key rings. Dimension 6 cm, thickness 5 mm. Contrary to my ornaments, they are indeed key rings. The plates which are used as supports are 15cm/10cm/2,6cm. Each color is set at a different height to allow for filament changes.
myminifactory
Get 50% off on Patreon: patreon.com/onepagerules Save BIG by buying this bundle, which comes with all of these models: - 1 Gator Veteran- 1 Gecko Starseer- 3 Snake Swarms- 1 Spinosaurus- 2 Triceratops Files are fully pre-supported!
thingiverse
Hi, I had a NEMA 14-50 socket for my Tesla Mobile Connector but it had a hole too big for the cable I used So I made a "cable gland" to cover that hole. The cable I used had 10.5mm diameter. ... I printed it on TPU, with suports.
thingiverse
Faceplate cover for a NEMA 14-30 dryer outlet or a NEMA 14-50 stove outlet using a duplex (double) outlet box. The four screws holding the plate are the same as securing the outlet to the outlet box. Usually these 240 volt NEMA outlets don't have...
cults3d
Faceplate cover for a NEMA 14-30 dryer outlet or a NEMA 14-50 stove outlet using a duplex (double) outlet box. The four screws holding the plate are the same as securing the outlet to the outlet box. Usually these 240 volt NEMA outlets don't have...
thingiverse
Faceplate cover for a NEMA 14-30 dryer outlet or a NEMA 14-50 stove outlet using a duplex (double) outlet box. The four screws holding the plate are the same as securing the outlet to the outlet box. Usually these 240 volt NEMA outlets don't have...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_holes_d = 6 solid_outer_border = 1 mount_hole_width = 40 mesh_clearance = 1 mount_hole_d = 3 mesh_thickness = 2 fan_side_length = 50...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: outer_diameter = 25 opening_width = 2 pressure_point_thickness = 4.5 nut_diameter = 8.5 diameter_top = 6.35 height = 30 articulation_thickness =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: outer_diameter = 30 opening_width = 2 pressure_point_thickness = 4.5 nut_diameter = 8.5 diameter_top = 6.35 height = 30 articulation_thickness =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: no_of_nuts = 1 retainer = 1 pulley_t_ht = 8 m3_dia = 3.2 pulley_b_dia = 20 nut_shaft_distance = 1.2 additional_tooth_width = 0.2 teeth = 20...
cults3d
Diameter external: 22mm Height: 35mm Screw: M3 Version: Nema 17 - 6mm Nema 17 - 6.32mm Nema 17 - 8mm My printer settings: Noozle: 0,4mm Extrusion Width: 0,45mm Layer Height: 0,2mm Top Layers: 4 Buttom Layer: 4 Outline perimeter: 2 Infill: Fast Honey...
thingiverse
RV, EV Power Cable holder for 240V 50A. ...I added a version without text and the step file.
thingiverse
NEMA 17 Stepper motor spacers 6, 10 and 22 mm
thingiverse
6 Round Magazine for T4E HDR 50. Works so far in mine. ...Good luck !
thingiverse
This coffee tamper for BORK coffee machines a little bit bigger - 50.6mm, cuz original 50 mm seems not enough dimensions. ... This 50.6 mm size is almost ideal!
thingiverse
... of http://www.thingiverse.com/thing:217046 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=217046 Instructions Using the following options: holeRadius = 2.6 thickness = 3 width = 10 hookRadius = 12 height = 50
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=378736 Instructions Using the following options: sides = 6 boxh = 50 thickness = 2 lidh = 10 parts = both diam = 70 looseness = 10