neptune 3 plus 3d models
798325 3d models found related to neptune 3 plus.thingiverse
this is a tool holder for the elegoo neptune 3 plus https://www.crealitycloud.com/en/user/3626193967
thingiverse
The elegoo neptune 3 plus is difficult to level sometimes. ...This test hopefully will help you figure out what needs to go up and what needs to go down.
thingiverse
Elegoo Neptune 3 plus parts draw Should fit the Pro and max. ...Let me know in the comments if you use it on other printer :-) May fit othere printers Print 2 and have one on each side :-)
thingiverse
I believe the default Neptune 3 Plus profile provided by Elegoo sets the initial layer height to 0.25mm. Because these squares are 0.2mm, these will not print if your initial layer height is set to 0.25mm. ...Set your initial layer height to 0.2mm for...
thingiverse
... to use for PLA or any other material in the 190-230 heat range. Sized and sliced to work with the ELEGOO Neptune 3 Plus, should work just fine with the Neptune 3 Pro and Neptune 3 Max. ... I included the untouched .stl of the tower as well.
thingiverse
This is my Simplify3D printer profile I've been creating to use with the new ELEGOO Neptune 3 Plus. It should also work just fine with Neptune 3 Pro and Neptune 3 Max, you just need to change the bed size on the "Output" tab (if you don't see that...
thingiverse
A mount for a Raspberry Pi to replace the default screen and mount on the Elegoo Neptune 3 Plus - for those using Klipper. It might fit other Neptune 3 variants, I am not sure. ... I used a Raspberry Pi 4, but the mounting holes are in the same place...
thingiverse
ELEGOO Neptune 3 Plus Tools rack and small draw. Should fit the Pro and max. Let me know in the comments if you use it on other printer :-) May fit other printers. ... The slide on one for the plus and max does not need screws, you have to undo the...
thingiverse
... I took just the drawer part off the tool holder in the original make and I added a drawer to it. ...Now it fits perfectly behind the screen on the right side of the machine. This will also work on the Neptune 3 Pro, Neptune 3 Plus, and Neptune 3 Max.
thingiverse
This simple tray to help you keep your environment clean. ... It snaps on the screews so it doesn't move.
thingiverse
A small part to replace the R shaped clamp to bend the wire a bit up preventing it hanging on the bed. The original screw can be used. you need two small zip ties. Caution: Be aware with this part you limit your maximum printing height! ... I used it...
thingiverse
Simple cover for the Spoolholder to cover the open hole!!
thingiverse
Found my Led strip coming loose, so a quick 11-minute fix, LED COVER, print in white or clear, OR if you like color try red. ...
thingiverse
Upgrade the positioning fixture of the Z-axis linear guide for Neptune 3 Max Plus, and it is recommended to print 3 or 4 of them. ... Use the platform board and Z-axis profile as references to position the linear guide.
thingiverse
Neptune 3 Spool holder, NO METAL PARTS NEEDED, no bearing or threaded rod, Just print and use. Tip, you may have to sand/file down the seam that the printer leaves on the inner spindle. Based an idea from the excellent XMAN_Prints spool holder. ...
thingiverse
I just remixed both designs to fit my Elegoo Neptune 3 Pro printer. With this remix you need less metarial and time to print with same durability. ... Notes for printing; - Better to use %10 support with lines (easy to remove so don't hesitate) - It...
thingiverse
Raspberry Pi Camera holder for the Neptune 3 Pro/Plus/Max Z Axis mount that I created. ... Mount Link: https://social.thangs.com/m/751446 Original model at thangs.com: https://social.thangs.com/m/751479
thingiverse
Case for the Raspberry Pi 3B+ (don´t know if other fit too) with clamps to fit snug on the frame of an Elegoo Neptune 3 Pro, Plus or Max
thingiverse
Holder for the Logitech C270 Camera to go on the Z Axis mount I created for the Neptune 3 Pro/Plus/Max. ... Mount Link: https://social.thangs.com/m/751446 Original model at thangs.com: https://social.thangs.com/m/751499
thingiverse
I am using the Sonic Pad with my Elegoo Neptune 3 Plus. I removed the now useless original display and created a camera mount which uses the screw holes of the display mount. I used the Knurled 1/4-20 Camera Mount Screw...
thingiverse
It's an accurate (with fillets and holes) 3D model of the Elegoo Neptune 3 Pro/Plus/Max and 4/4 Pro build plate to be used as a custom background in PrusaSlicer, SuperSlicer or Cura. I've added an embossed Elegoo-logo for a slightly refined look.
thingiverse
I made a cover for the screen connector, I am using klipper and the factory touchscreen is not compatible.
thingiverse
To reduce the dragging friction of the filament which can cause instability in 3D printing, especially for those printers that have the filament spool on the upper crossbar, I thought of replacing the default spool holder of my Eleggo Neptune 3 PRO...
thingiverse
I upgraded my Neptune 3 Pro with a Slice Engineering Copperhead C-E heatbreak and made this simple tool to cut the PTFE tube (⌀ 4 mm) at the right length (37.6 mm) and chamfer it at 120° angle. You will need a sharp scalpel to use it. ... Appreciate...
thingiverse
Just took 3Dtcb's design and shortened the arm so that it doesn't protrude as much. ...great if your webcam has a wide angle lens
thingiverse
This is the Raspberrypi 3 A plus / 3A+ case from guysoft (https://www.thingiverse.com/thing:3394092) customised to fit into the rails of the Elegoo Neptune 2. ... I also added a hole for the camera cable.
thingiverse
Mk2 of My tools rack. ... Would love to see you’re makes.
thingiverse
An adapter to attach a Creality bearing spool holder to a screw on style arm.