nikko dictator 3d models
670 3d models found related to nikko dictator.thingiverse
Part that holds the wheel on a Nikko Dictator 2. I use an electronics desoldering heat gun to heat up the wheel axle, and then force it into this printed part using a vice in order to replicate the hobbed area. Will upload some pics later, when...
grabcad
Nikko dictator rear damper support (use with M3 screw or drill M4 for using original pivot).
thingiverse
Set of printables to adapt a LiPo Battery to my Nikko Dictator 2. The side stops are replaced for longer ones, and I added 2 Battery protections, since I bought a LiPO soft pack. Side Protections (print 2 of them) have embedded breakable support by...
thingiverse
a part I modelled for an old R/C car which was broken (front knuckle)
thingiverse
Hook to hang a Nikko Dictator 2 to the ceiling of my garage. Designed to hold the car vertical, by the 2 rear square rings. ... Deisgned with...
thingiverse
Customized version of https://www.thingiverse.com/thing:3149903 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3149903
thingiverse
Customized version of https://www.thingiverse.com/thing:333292 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=333292
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: slitwidth = 2 slitlength = 2 line_spacing = 2 line_9 = line_8 = line_7 = line_6 = line_5 = line_4 = line_3 = line_2 = line_1 = NIKKO font =...
thingiverse
This coupler is used to connect 2 Worker Talon magazines together so they are compatible with Dart Zone's Dictator foam blaster. *This file will need to be rotated in your slicer to avoid using supports. (I'll update the orientation of the file...
cults3d
Waging war for The Dictator; this is a sample figure from my Dictator Walker Crew set; All samples are from sets that preview on my Patreon and then port over to Gumroad the month after they are offered. ... https://gumroad.com/bigmillerbro ...
cults3d
Waging war for The Dictator; this is a sample figure from my Dictator Tank Driver set; All samples are from sets that preview on my Patreon and then port over to Gumroad the month after they are offered. ... https://gumroad.com/bigmillerbro ...
cults3d
Waging war for The Dictator; this is a sample figure from my Dictator Army Trooper set; All samples are from sets that preview on my Patreon and then port over to Gumroad the month after they are offered. ... https://gumroad.com/bigmillerbro ...
thingiverse
Waging war for The Dictator; this is a sample figure from my Dictator Tank Driver set; All samples are from sets that preview on my Patreon and then port over to Gumroad the month after they are offered. ... https://gumroad.com/bigmillerbro ...
thingiverse
Waging war for The Dictator; this is a sample figure from my Dictator Army Trooper set; All samples are from sets that preview on my Patreon and then port over to Gumroad the month after they are offered. ... https://gumroad.com/bigmillerbro ...
thingiverse
Waging war for The Dictator; this is a sample figure from my Dictator Walker Crew set; All samples are from sets that preview on my Patreon and then port over to Gumroad the month after they are offered. ... https://gumroad.com/bigmillerbro ...
thingiverse
If you have a large format printer, you will need: 2x thanhlon_dictator 2x [ThanhlonFollower](https://www.thingiverse.com/thing:3460408) 2x [Drum Spring](https://outofdarts.com/products/replacement-drum-spring-created-by-foamblast) If you have a...
prusaprinters
Improved Trigger for the Dart Zone Dictatormuch less slack on the trigger pull. prints without supportssnap-together (PETG recommended to allow flex-snap)
thingiverse
This is a replacement joystick for a Nikko RC Car. ...The joystick is about 5mm longer than the original.