nikon f2 waist level finder 3d models

i made this for a 37mm diameter 5x enlarging glass I had lying around. ...abs print

This is a file for a Light to illuminate the light meter and shutter speed within the finder of a Nikon F2 when ambient light is not strong enough to do naturally. The device fits snugly on my F2 and does not fall off easily even if the camera is...

This is a file for a Light to illuminate the light meter and shutter speed within the finder of a Nikon F2 when ambient light is not strong enough to do naturally. The device fits snugly on my F2 and does not fall off easily even if the camera is...

Quick, Diry, can't fold but funktional Kiev 88 Waist-level finder.

Quick, Diry, can't fold but funktional Kiev 88 Waist-level finder.

Designed this to go with the adapter plate I remixed for the Bronica SQ-Ai. ...The waist level finder is very hard to find these days so this provides an alternative solution.

Replacement pop-up cover for waist level viewfinder on Mamiya M645. Can be assembeled with 2.75 mm steel rods or with included printable rods. ...Current print underway now, will update with finished photos

... of the Waist level finder consists of two parts. To assemble the Waist level finder it needs some manual dexterity, because the small springs have to be wound by yourself. For the hinges I used both, wire pins and screws. ...Both are possible.

I was blown away by the cost of an OEM Waist Level Finder for my Mamiya 645 Super. I don't use one often but when you want one you want one. So I came up with this. I will probably replace the front tabs with 1mm stainless once they break off. I...

I was blown away by the cost of an OEM Waist Level Finder for my Mamiya 645 Super. I don't use one often but when you want one you want one. So I came up with this. I will probably replace the front tabs with 1mm stainless once they break off. I...

The Nikon F2 is a professional level, interchangeable lens, 35 mm film, single-lens reflex (SLR) camera. It was manufactured by the Japanese optics company Nippon Kogaku K. K. ...(Nikon Corporation since 1988) in Japan from September 1971 to 1980

Remixed to make it fit Bronica SQ-Ai. Added notch in the back and adjusted the position of the locking hole. ...Also filled in the long slot to allow release.

A basic iteration of this - I've stuck a hole in the body cap and added a box with a hole for the hood. I've not seen one of these released under a CC license. Size of the indentation for the hood to slot into is 60x55mm. I'll probably tidy up the...

Want a better grip for your old analog Nikon F2..... HERE IT IS! - Keeps the original look of the camera. - Greatly increases the comfort of the camera. You will need a standard 1/4" thumb screw to attach it to the tripod mount at the bottom of...

This adapter allow to use Hasselblad / Kiev88 / Salut-S / ARAX 88 waist levels on Bronica SQ. You can print full body if you professional in work with supports. ... But I print top and bottom separately and glue it together by cyanoacrylate.

A cover piece for action finder, Nikon F.

Finder level relay 72 series

This is a foldable waist level finder for RED Komodo. This part was designed to be printed with TPU. (Preferably with 95A hardness) As TPU can be quite tricky to print, especially with thin walls like in this part, i recommend adjusting your Z-seam...

Made to fit Nikkor 14-24mm F2.8 Lens. The uploaded arduino code may need to be updated (written over a year ago). Fun idea: Print this with glow-in-the-dark filament for afterglow. ...=D NeoPixel: https://www.adafruit.com/products/2874 Vid 1:...

Customized version of http://www.thingiverse.com/thing:1060283 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1060283 Instructions Using the following options:...

This is a replacement piece that holds the auto leveling sensor in place on the Flashforge Finder. ...This is the factory size but I have included the Sketchup file as well in case anyone would like to modify it.

... to tune it in to get it nice and leveled. ... Looked around and found an on the fly generic bed level test here: https://www.thingiverse.com/thing:97151 but it was too big to fit on the Finder. ... Took out the last ring and set the height to 0.2mm.

This is a replacement piece that holds the auto leveling sensor in place on the Flashforge Finder. This is the factory size but I have included the Sketchup file as well in case anyone would like to modify it. ...Print Settings Printer: ...

Tripod clamp for the Nikon 80-200 f2.8 D Lens (Push-Pull version). Print all four parts and screw them together using M4 screws. You will also need a metal plate to screw in the mount (Arca Swiss, etc.). The opening at the bottom of Part 3 has to...

... and 0.2mm in height. It is the size that can output 1 layer to the maximum allowable range of my printer. Whether or not the level is right can be seen from the output. ... The areas where bed is not closely attached are different in density.

The system is dedicated to the Nikon 80-200 F2.8 ED lens. It makes it possible to make a precise focus and to block this focus for astrophotography. The system consists of a collar to be fixed on the lens (smaller diameter) and another mobile...

The 35mm f2.8 lens found on a Nikon L35AF point and shoot camera is rightly highly regarded as a quality 5 element sonnar lens, and is unusually wide for a fixed lens camera. It is not hard to find a broken model as the early electronics driving...

F2

This is an adapter for using Nikon's angle view finder for the polar scope in a Skywatcher mount EQ3. It is printed in parts and glued together. ... Some filing might be required for perfect fit of the viewfinder.

Unfortunately, Nikon didn't think to design it with a tripod collar. With the advent of mirrorless cameras and lens adapters, this lens puts too much stress on the lens mount. This collar redistributes the weight to prevent possible damage to your...