nixie socket 3d models
38867 3d models found related to nixie socket.thingiverse
... the diameter of your contacts and change the pin hole size in the customizer to get a working socket. Data and photos of an original socket: http://www.tube-tester.com/sites/nixie/data/soc/SK-136-12pin-chassis-russ/SK-136-12pin-chassis-russ.htm
thingiverse
its a snug fit, I drilled the outer holes to 1.1mm to clear any blobs, slot the tube into the socket, then partially seat the pins in the back. Heat from a soldering iron seats the pins the rest of the way, and locks them in. ...The tube helps make sure...
thingiverse
Just a simple IN12 Nixie lamp socket. The pin-holes are 2mm, and you can use precision goldpin (or IC sockets) pins. When you get them off, you should drill them with 1mm bit. ...Then just put them in printed socket, and there you go.
thingiverse
Customized version of https://www.thingiverse.com/thing:3198271 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3198271
thingiverse
Tube socket that fits over pins of IN-12b sowjet nixie tube. Do not attempt to bend the pins of IN-12 nixie tubes because the glass will shatter. The holes are close fit to the pins but the socket should slide over the pins easily. ... Before...
thingiverse
I couldn't find any pre-made sockets for the IN-1 sized nixie tubes. These nixies are cheap on eBay because they cannot be backlit with LEDs, but they still glow nicely. Sockets for them are very hard to find for sale, so I decided to make one that...
thingiverse
I needed a socket for my IN-2 nixie tubes. So here it is. Screw holes are for 4mm screws. The height of the socket works nicely with walls which are a couple of millimetres thick. The wooden wall in the last photo is 3mm. The metal pins have a...
thingiverse
Using a soldering iron and little screwdriver to apply mild pressure the connectors can be sunk into the plastic socket. When all connectors have sunk in, turn the socket around and keep it firmly on the table resting on the connectors. Then with...
thingiverse
Customized version of https://www.thingiverse.com/thing:3198271 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3198271
thingiverse
IN-8 Nixie socket designed to fit into a standard breadboard. I used pins from a 90 degree header and pressed them into the side of the print holes. This print is very small and the tolerances are tight so I recommend using a small diameter print...
thingiverse
Requires a soldering iron to melt the tube mating pins in place.
thingiverse
I wanted a way to mount the IN-18 Nixie tube holders. I made a single block, and a block of four. I plan on using these for mounting the tubes for experimentation, and possibly building the final device. ... The single block is about 1mm...
thingiverse
... part of a nixie tube socket for IN-14 nixie tubes. ...It's designed to be used with nixie tube socket pins like these: https://www.ebay.co.uk/itm/50pcs-Nixie-VFD-Tube-Socket-Female-Pin-for-IN-14-IN-16-IN-19-QS18-12-QS16-YS13-3/174283555500 (see photo).
grabcad
Socket pin model for nixie tubes like IN-12, IN-18 with 1mm pin hole
thingiverse
... lid was held on with toothpicks. ... I ended up just heating up a small finishing nail, and pushing it in. Project Blog: Nixie Tube Fun Note: Hobby Lobby are a bunch of liars, and that does not come as a three pack. ... It's a single box.<BR> <BR>
thingiverse
Socket for russian nixie IN-18 and IN-4. ...Original drawings from: http://www.nocrotec.com/shop/product_info.php/info/p36_IN-18-IN-4-Nixie-Tube-Socket-with-blue-LEDs.html
grabcad
# Nixie-DisplayMulti purpose LCD display, with nixie tubes for numeric valuesLink to PCB:http://workspace.circuitmaker.com/Projects/Details/Hartvik-Line/Nixie-DisplayLink to GitHub:https://github.com/Hartvik90/Nixie-Display/edit/master/README.md
grabcad
I tried to make a Nixie Tube, but the most detailed possible, so I searched some pictures of the inside, and found those...
thingiverse
... well, but perhaps someone else can improve upon it. Details about the project: http://www.nycresistor.com/2011/10/15/el-wire-nixie-tubes/ Instructions Cut out of 3mm clear acrylic. ... Tape the EL wire to the numbers and press-fit to the frames.
sketchfab
A clock made out of nixie tubes, made this as a project for Uni and got to experiment with Opacity finally. ...In depth showcase here: https://www.artstation.com/artwork/rRrLy2
thingiverse
Instructions Nomenclature : 1 x Nixie Tube Clock ‘Nixie QTC’ from www.pvelectronics.co.uk 6 x Nixie tube IN-14 1 x 105, 2 x 102, 2 x 106, 2 x 107, 1 x 108, 1 x 109 8 x Insert type c M3 8 x Screw CHC M3-10 4 x Screw CLS M3-10 4 x Nuts HM3 12 x...
thingiverse
This is the first try to create a housing for my nixie watch. I found the schematics and the code at Instructables and changed it to my needs. ...The processor is a small arduino mini and the tubes are ZM1325.
sketchfab
Pinkmoth‘s character Nixie! Check them out on twitter! ...A few parts got a little messed up in the upload (like the arm coils), but it’s still %99 intact.
cults3d
This is the first try to create a housing for my nixie watch. I found the schematics and the code at Instructables and changed it to my needs. ...The processor is a small arduino mini and the tubes are ZM1325.
grabcad
This is a CAD i made with Rhino CAD for mac. ...This Nixie Clock I build in real too. ...Photos enclosed.
thingiverse
UNTESTED BETA! ...This is a casing for a 1 digit IN-4 Nixie clock. It has not been printed yet, so be careful with dimensions. ...Update 12-06-2012 added an openscad-version, this should be better for printing though less curved.