laser snapmaker 3d models

Support for the bed of the Laser Snapmaker 2.0 used in the A350 Printer: Snapmaker 2.0 Mode: Fast Print + Support 15% Rotate the part 180º on the x axis There are two supports in the files, a support for magnets of 20x10x3 and another of 11x6x3 PLA

... to be a raised bed for use on the snapmaker 3 in 1 printer. ...This addon, is for use under materials like paper so that you don't laser your base. ...Highly recommend that you print using RAFT, as it makes small diamonds that may lift off bed.

This 3d .stl file is a shield for the Snapmaker laser module. I printed it face (lettering) down with no supports and 50% infill to prevent arms from breaking off. Shield floats on the module and attaches to the module by sliding over the top. It...

Once I had my focus set I extended the stand between the top of the etching surface and the bottom of the laser housing. Then I glued it together and can now use it for every engraving. ...I just set it on the surface to be engraved and lower the...

Snapmaker will go second passes to laser cut. ... 3.If you want generate Gcode by yourself, making sure adjust size to 80 x 80mm; Set work speed 80~120 mm/minutes 4.Tool: flat end mill Tutorial Video: https://youtu.be/FndY6A_jF1s Maze Gaming:...

This is necessary because Snapmaker Luban will mix up the inside and outside cuts when calculating the toolpath. The inside shapes file should be cut first. I was able to separate the inner and outer cuts using lightburn. Unfortunately, Luban is...

First off, attribution: This is a remix of the laser bed corner inserts by morpha on thingiverse.Found here: https://www.thingiverse.com/thing:4857543 During my testing, I figured out the true 0,0 of the Snapmaker A350 (at least mine) is at X-2,...

This Snapmaker Luban file will etch 100 circles, each with a different power/speed setting so that you can quickly determine what settings work best with your given material. Prints in about 15 minutes! Scales from 10% to 100%, and 600 - 6000 mm/m...

... Note: The cone is taller then it needs to be depending on the focus of the laser. Printed with vase mode and cut down after the laser was focused on the object. ... Recommended items needed: Super glue Tip if you want updates or modifications

Instead of removing heat bed, you can us this clips to attach laser bed over heating bed. This print include front big, front small, rear big, rear small and front middle clip. You need minimum 2 Front Big, 1 Front Middle and 2 Real big clips. ...

I purchased the glass at (...

Deutsch Schutzkappe für den original 10W Laser von Snapmaker 2.0. Ich habe hier nur Kappen für den kleinen Laser gefunden, darum hier das neue Design. Das Design hat eine Presspassung und rutscht nicht von selbst ab, daher empfehle ich den Druck...

# Laser Exhaust Attachment for 10W Snapmaker Laser ##[Mini Dust Collection](https://www.thingiverse.com/thing:5805774) ##[Exhaust Extension](https://www.thingiverse.com/thing:5847318) ##[Snapmaker Vacuum...

Check it for more info : https://www.thingiverse.com/groups/snapmaker/forums/snapmaker-guidebook This is a simple sleek shell to create a Snapmaker 350mW Laser engraving module. ... If you want to rebuild this Laser engraving module check out my...

**Update to new version: Added cutout for auto-thickness laser, further recessed lasers to allow for manual thickness while cross is still attached** This is a laser cross I designed for the Snapmaker 2.0 10W laser. I got tired of trying to find the...

This alignment tool is used to get an exact reproducible position for the parts being laser engraved. ... It fits on the laser bed of the Snapmaker 2 (tested on A250 and A350) and is fastened with the same screws as the bed itself. ...

This was made in Snapmaker Luban for a Snapmaker A350. Not sure how it will work on other laser machines. Try it out and let me know. It cuts lines from 10% to 100% power @140mm/min, 2 passes, 0.6mm pass depth (vector) Grayscale squares from 5%...

This was made in Snapmaker Luban for a Snapmaker A350. Not sure how it will work on other laser machines. Try it out and let me know. It cuts lines from 10% to 100% power @140mm/min, 2 passes, 0.6mm pass depth (vector) Grayscale squares from 5% to...

Noise dampening pad for Snapmaker 2.0 (probably 1.0 as well) laser bed. The stock bed is only fixed in the centre and rattles as it moves. I printed some of these out of TPU and put them on the attachment points (all of them, not just the ones with...

Noise dampening pad for Snapmaker 2.0 (probably 1.0 as well) laser bed. The stock bed is only fixed in the centre and rattles as it moves. I printed some of these out of TPU and put them on the attachment points (all of them, not just the ones with...

This was made in Snapmaker Luban for a Snapmaker A350. Not sure how it will work on other laser machines. Try it out and let me know. It cuts lines from 10% to 100% power @140mm/min, 2 passes, 0.6mm pass depth (vector) Grayscale squares from 5%...

This was made in Snapmaker Luban for a Snapmaker A350. Not sure how it will work on other laser machines. Try it out and let me know. It cuts lines from 10% to 100% power @140mm/min, 2 passes, 0.6mm pass depth (vector) Grayscale squares from 5% to...

I try to get to the initial position(Z offset) of the laser. ... The height obtained through the plywood is 30 mm between the laser module and the platform. ... Change height 30mm --> 27mm

Previous Laser bed had not underlying support, which I found to be a pain to print. This version has its own raft as part of the object which will give it more stability and also make it easier to print. ... It is intended to use after with the laser...

Darthwolf's clips are a great idea, but for me they just loosely sat in the laser bed and didn't really do anything. Instead, I've redesigned it with wedged feet so that it squeezes in between the slots and can hold a piece down. Video Category: 3D...

Darthwolf's clips are a great idea, but for me they just loosely sat in the laser bed and didn't really do anything. ... Instead, I've redesigned it with wedged feet so that it squeezes in between the slots and can hold a piece down.

Laserplattenhalterung für Snapmaker A350

The moveable element has been designed such that it will allow you to use the rubber plugs that comes with the Snapmaker to secure it to the laser bed. ... I will hopefully amend this design in the future to allow holding down items that bow or lift...

A remix of https://www.thingiverse.com/thing:4808986 to avoid having to screw the guide down. ...Can be used with https://www.thingiverse.com/thing:4823121 to quickly change the build plate from 3d printing for laser work.

This air assist nozzle helps to decrease residue when laser cutting wood. Just slide it over the cover of the 10W laser. You can fix it with an M3 screw. If needed, you can slightly increase the inner diameter with a file. Additional compressed...