nodemcu multisensor 3d models
1564 3d models found related to nodemcu multisensor.thingiverse
Based on bruh nodemcu multisensor project. Needed a box that was easier to place in corners. Light sensor needs to be glued inside front panel with sensor in the small hole. ...All electronics is the same as https://www.thingiverse.com/thing:2239142
thingiverse
It is designed to isolate the NodeMCU from the sensors by filling the wire pass-through holes with hot glue.Lid is designed to be glued as well. Access for reset and flash buttons is provided so it can be reflashed without opening. Basically, it's a...
thingiverse
A revised version of the Bruh Automation and TrueOverFlow multi-sensor case that includes: Space for BH1750 light sensor Higher stand-offs for NodeMCU Amica board Pinch-clip at bottom of case to hold it together more effectively Parts list to...
thingiverse
It mounts together very easily, just solder your components together and pop the NodeMCU into the casing. Then slide the sensors into the slots in the cover and click the cover on top of the case. No screws needed! This is my first design, and I...
thingiverse
Video Tutorial - https://youtu.be/jpjfVc-9IrQ This enclosure is for DIY Multisensor that can be built using a NodeMCU 1.0 ESP8266 development board. It works great with Home Assistant - my favorite open-source, home automation platform. no...
thingiverse
A new design for BRUH Multisensor - The Burger Box... Thingy original with all information about the electronic parts and code can be found here: https://www.thingiverse.com/thing:2239142 thanks Ben... Please Comment or send message if you find...
thingiverse
... internal parts and leave the connectors "as is"... ... Link to BRUH original with all the parts of the NodeMCU and sensors: https://www.thingiverse.com/thing:2239142 If you love it give BRUH thumbs up :) License remains as original creator intended..
thingiverse
... can be easily mounted on a wall or the ceiling. Changed the nodeMCU mounting slot. Using M2.5 12mm screws for the assembly Fits the NodeMCU v3 https://www.banggood.com/custlink/D3D3dNUAZ0 M2.5 screws: https://www.banggood.com/custlink/3GGmEn2bMH
thingiverse
This is a completely new design to incorporate the larger Pyroelectric IR Infrared PIR Motion Sensor Module Detector HC-SR501 I have these running in every room now, a very cheap solution to enable lots of additional automations on Home Assistant...
thingiverse
... of enclosure is slightly bigger than original so that nodemcuv3 can fit inside. Thanks and credits to Bruh Automation for original design. https://www.thingiverse.com/thing:2239142 https://github.com/bruhautomation/ESP-MQTT-JSON-Multisensor
thingiverse
Multisensor unit with a great design that make it suitable for a side table I have made two units one with NodeMCU+PIR sensor+ AD2301 (removed the original black cover used only the PCB) the second unit I used NodeMCU+PIR sensor+ DHT11+ and light...
thingiverse
##Partie NodeMCU Mettre les fichier temp.png hum.png et monserrat.ttf dans le repertoire config d'esphome. Le code ESPHome : <pre> esphome: name: Nom du sensor platform: ESP8266 board: nodemcuv2 wifi: ssid: "monreseauwifi" ...
thingiverse
Caixa para multisensor. ...Além do NodeMcu e sensores correspondentes leva também o transformador AC-DC 5 V 700mA 3.5 W.
thingiverse
Remixed from @bruhautomation NodeMCU Multisensor, thanks! This has been scaled larger to fit the NodeMCU v3 as the original model was too small. It also only has cutouts for the DHT22 sensor and ventilation. ...I don't use the other sensors so I...
thingiverse
This is a case for a multisensor using a Amica NodeMCU, Light sensor and Temp/Humidity Sensor. It is designed to hold the NodeMCU in the lid and have space for wires in the bottom. The holes are sized for jumper wires to fit through. Pegs are there...
thingiverse
Thanks for the case @ calvinboey Modified it so it fitted the parts of the BRUH's Multisensor: https://github.com/bruhautomation/ESP-MQTT-JSON-Multisensor DHT22 temperature sensor DHT22 humidity sensor AM312 PIR motion sensor TEMT600 light sensor RGB...
thingiverse
I wannted to make a box to include all motion sensor, temp sensor and a nodeMUC, Hardware used: Temp\Humidity sensor (AH2301) PIR (HC SR501) note: you need to make a separation between the Temp sensor and the NodeMCU otherwise temp reading will be...
thingiverse
I opted to mount the nodemcu on the side for (I think) easier cable management. DHT22 mount/cover remixed from http://www.thingiverse.com/thing:480481 DHT22 can be screwed down but the fit is pretty snug and will snap in. Lid is also just...
thingiverse
Fitting piece for fibaro sensor to fit Multisensor 6 Recessor
thingiverse
Outdoor mount for the Fibaro motionsensor. ...Print it yourself or buy it at www.ROBBshop.nl. click on the linkhttps://www.robbshop.nl/montagebeugel-multisensor-fibaro-buiten
thingiverse
Recessor for Aeotec Multisensor 6. First version was printed in two pieces and mounted as a sandwich. The "onepiece" version is a newer version intended to be printed in one go. ...My personal favourite is the square version.
thingiverse
Mounting adaptor 92mm to 68mm cavity wall installation box, suitable for a Steinel Multisensor. ... You can use the screws and latches from another cavity wall box to mount the adaptor.
thingiverse
... all the holes for the sensors and the ventilation outlets and the hole for the power cable. It accommodates all sensors (PIR AM312, DHT22, Photoresistor and a DIP 3-color LED Module), all with nodemcu, jumperwires and without any type of welding.
thingiverse
I uploaded an example of the esphome yaml configuration I use for my multisensor. I was in the process of fine tuning the code when I posted this. So there is one version without a beeper and with dallas temp, and another without dallas temp and...
thingiverse
A riser/tower to fit a Fibaro Multisensor. ...Kind of inspired by Sauron's tower in LOTR.
thingiverse
DIY multisensor -RCVL0516 presence sensor -BH1750 light sensor -BME280 temperature humidity preassure -IR reciever -5mm IR led transmitter -WS2812 adressable led pixel -D1 mini (Tasmota firmware)
thingiverse
Multisensor box by www.pihrt.com https://pihrt.com/elektronika/448-esp32-multisnimac-hw1-1-pro-opensprinkler-system OpenSprinkler system https://github.com/martinpihrt/OSPy and https://opensprinkler.cz/