odrive 3d models

Basic case for [ODrive controller](https://odriverobotics.com/)

This is a quick and dirty front and back plate with Encoder fittings for testing your ODrive.

- use 2.5mm screws for plastics, e.g. ...BOSSARD 2000164, and/or M3 screws to mount the odrive PCB - mounting flange with M8 holes

Dummy models of the odrive brushless motor controller to use for mockups or test fitting parts. ... I've included one PCB with just the caps that is able to print flat on the bed, and another with every part on the board.

oDrive D5065 - 270KV bldc

oDrive D6374 - 150KV bldc

ODrive - High performance motor control

This is a Din rail clip for the Odrive from Odrive robotics, print one normal and one mirrord, install with din tabs facing out.

ODrive Actuator Parts Encoder, ODrive 6374 Motor, Front Motor Bracket, Ballscrew Cover 4 CF tube, Ballscrew Housing , bearing Cap to align rear of shaft

This set of parts provides a nice housing for the D6374 ODrive out-runner motor.

Representative model of oDrive D6374-150KV BLDC Motor. Dimensions are based on available data and actual measurements. ...Interior dimensions of motor are estimated.

Simple bracket to mount stack of odrive's on din rail. ... Clamp outline captured from gorgeous project: https://www.thingiverse.com/thing:2613804

actuator parts for ODrive 6374 BLDCBearing CapRear Encoder HousingFront Motor Housing Back Bearing Housing for Ball screwFront DIY- IGUS for 30mm OD CARBON Fibre Tube

ODrive motor board protective case You can use with or without two fans on both sides. Fusion360 files included if you want to modify it. ... Prusa i3 MK3 0.2 20 infill PLA without support

ODrive motor board protective case You can use with or without two fans on both sides. Fusion360 files included if you want to modify it. ... Prusa i3 MK3 0.2 20 infill PLA without support

The ODrive sits on the pins on the bottom cover for location and is then held in place by the top cover and four screws. The diameter of the holes are 2mm so please select fasteners accordingly. This case does not have mounting locations for...

ODrive Enclosure. Has room for 3 40mm fans, however venting with all three in place is insufficient. I plan to use the outer two positions, and leave center as a vent. ...Top is held in place by tabs that lock to the feet, it may not be secure in high...

Support moteur odrive robotics 270Kv pour profilé aluminium 20x20 (https://odriverobotics.com/shop/odrive-custom-motor-d5065) Les autres pièces (poulies et autre) sont sur mon profil

Made for m3 heat-inserts.

This is Odrive 3.6 case Rimix with https://www.thingiverse.com/thing:4598641 with few modifications. The break resistor is inside the case but I'm testing the heat increase. I might add some locations for the fans later. ... please give me your...

A remix of a case for the Odrive motor controller board. https://odriverobotics.com I added connections for 30mm cooling fans. There are two version of the top, one with 3 fans, which is a little bit taller, and one for 3 fans that still lets you use...

A more photorealistic model of the large motor sold by ODrive Robotics

A 3D Printable SCARA for use with ODrive for use with timing belts.

I decided to share my more detailed version of the smaller size motor sold by ODrive, enjoy!

A quick and dirty motor holder for N5065 brushless motors with an encoder. ...This is designed for using it with the ODrive board: https://odriverobotics.com/

Motor Housing for ODrive D5312S Motor Printable housing to enclose D5312S motor. Use M3 threaded brass inserts with the housing plate. Back plate includes holes to attach an CUI AMT102-V encoder. Clearance/through holes for M3 hardware. Note: The...

First attempt

A Motor Holder for a 9235-100KV Turnigy Multistar brushless Multi-Rotor Motor, with space for an 8192 CPR ENCODER. ...Then encoder is mounted between the motor and the 80mm fan.

1/ 6374 -75-OD Face plate with recess for housing2/ 6374 -75-OD Back plate with AMT 102-V recess plus recess for housing3/ 6374 -75-OD housing4/ 20.5 Ball screw fitting for 24x22 Carbon fibre tube to make linear actuator.

2019 Update: Model modified so that it matches the current production run of Odrive D6374 motors. ...The previous model was for pre-production motors.Odrive D6374 3D printable low profile encoder mount for AMT102 encoder