picatinny handguard covers 3d models
140935 3d models found related to picatinny handguard covers.thingiverse
Bought a red dot for my airsoft ak and wanted to mount it and realized that there are no handguards so decided to make one Print at 100% infill and default orientation, enable supports
thingiverse
Extended handguard for SG22 (SpaceGat22) remixed to have a picatinny rail for accessories. ...Should be big enough for most grips or a bipod or whatever you have.
cults3d
M16A1 handguard rail or similar to be able to add a picatiny for different accessories such as foregrip or flashlights For the installation it is necessary 2 M4 bolts of 10mm
thingiverse
Update 09/02/2020: Added Clip 6 (hexagons) Update 03/21/2020: Added Clip 5 and modified all to remove the need for support. ... Individual slot covers for picatinny rails. ... 4 different styles.
myminifactory
Picatinny rail covers not only look cool but also protect the rails from damage and provide a better grip on the rifle. But most importantly, they look cool. No extra hardware needed, simply print and go! ...They are easily removed with a small...
prusaprinters
Edit 09/02/2020: Added clip 6 (hexagons). Edit 03/21/2020: Added Clip 5 and modified all to remove the need for support. Individual slot covers for picatinny rails. 4 different styles.
thingiverse
Hi everyone This is lower or handguard (not sure what is correct) for airsoft MP-5 kurz with 3 picatinny rails. i planned it to use with fake PEQ with battery on one lateral side and flashlight on opposite side and hand grip on lower side. ... Printing:...
thingiverse
45 degree Picatinny Rail for the Colt M733/CAR15 longer carbine handguards (different from M4/M933). These fit in place with the ribbing on the handguard and fix through the front 3 holes with use of M5 Nuts and M5 x 8mm Flanged Bolts. This gives a...
prusaprinters
45 degree Picatinny Rail for the Colt M733/CAR15 longer carbine handguards (different from M4/M933). These fit in place with the ribbing on the handguard and fix through the front 3 holes with use of M5 Nuts and M5 x 8mm Flanged Bolts. This gives a...
thingiverse
I remix this uzi handguard to fit a well r1 airsoft uzi. ... mounting holes are not yet in right spots might edit later
thingiverse
This is a picatinny rail cover I made which has skulls on them. ...One is vertical and the other is horizontal.
cults3d
Apart from covering an aesthetic flaw that most users consider important, it adds 2 95mm picatinny rails or 9 slots on both sides, to use accessories such as flashlights, lasers, cameras, rifle racks. ... Mounts with 4 3x12mm or 1/8 x 1/2 inch...
thingiverse
Fits into the slots left by the stock Rapidstrike rails, and allows for picatinny rail compatibility. Cover works for 132 motors but untested with 180 motors. Print CoverRail upside down. ...I recommend printing without support, but you can also...
thingiverse
A set of 5in long Picatinny Rail covers integrated with E-11 T Tracks, for custom blaster conversions! There are 3 versions- Thin, which snaps over if using PLA+ or PETG, Thin with Tab, which has a tab to prevent it from sliding back and forth, and...
thingiverse
Picatinny Rail for standard Airsoft M4/AR15 Handguard. ... I design it for 2 or 3 M5x15 bolts.
myminifactory
... NOTE: I haven't had a chance to print the whole thing to try it out yet, just the bottom half... ... This is a handguard with picatinny rails for my paintball marker. ...Attached are the .stl files for it not split and for it split (top and bottom).
cults3d
NOTE: I haven't had a chance to print the whole thing to try it out yet, just the bottom half... ... This is a handguard with picatinny rails for my paintball marker. ...Attached are the .stl files for it not split and for it split (top and bottom).
thingiverse
... ... This is a handguard with picatinny rails for my paintball marker. Attached are the .stl files for it not split and for it split (top and bottom). Instructions This thing was made with Tinkercad.
thingiverse
Zur Verwendung mit dem Griffstück vom M4-Umbaukit von Buck Rail (https://buck-rail.com/product/diana-ar-conversion/) und dem Picatinny-Adapter für Zieleinrichtungen von Schlottmann...
thingiverse
Hi everyone This remix based on https://www.thingiverse.com/thing:443782 https://www.thingiverse.com/thing:4757 A lot of thanks from me to designers who made these things This is lower or handguard (not sure what is correct) for airsoft MP-5 kurz...
thingiverse
Turn OFF uniform scaling, you only want to stretch in one direction!!!) For the Top Cover, you can insert any tube of 16mm outer diameter. For those unable to acquire basic shapes, I included a version with tube. --------------------- ##In...
cults3d
Includes 9 versions: - handguard_minimized have keymod slots on both sides and bottom(this one integrated into rail), rails on top and bottom - clean_rounded: rail on top and bottom, rounded sides (no holes on sides) - clean_flatside: rail on top...
cgtrader
Modeled in Blender includes materials and textures Multiple size rails and covers
thingiverse
Standard Picatinny rail , which can be used as fastening devices on airsoft guns as well as almost any other subject . Of course, if you can attach the bar to this very subject. ) Has two versions: with Hole bolt without them. ...