playseat challenge mount 3d models

I wanted a robust shifter mount for the Playseat Challenge, and used the https://www.thingiverse.com/thing:2914511 as basis, creating a non adjustable and sturdy mount. Use three 6mm bolts to mount it to the Playseat. ...

I wanted a robust shifter mount for the Playseat Challenge, and used the https://www.thingiverse.com/thing:2914511 as basis, creating a non adjustable and sturdy mount. ...Use three 6mm bolts to mount it to the Playseat.

* Install ZipTies in mounts * Tighten ZipTies around Playseat Challenge by pulling down then pulling up * Trim ZipTies Requirements: ============ * 1x 5mm Allen Key * 1x 10mm Wrench * 8x ZipTies 5mm * 2x M6x16mm Socket Head Bolt (low profile, so it...

https://mount-it.com/collections/tv-mounts/products/vesa-pole-mount-mi-390 Use code: HONEY15 for 15% off, $25.50 with free shipping https://vkbcontrollers.com/?product=gladiator-nxt Hardware: The top M8 bolt needs to be shortened by about 12mm. ...

v2 of the mount, very easy and fast to install with 8 large zip ties and 4 pcs M6 x25 screws the Logitech G29 pedal to Playseat challenge seat Also working with Thrustmaster t300 RS Print instructionsPETG, print 2 times the G code or 4 pcs,...

... moved to printables.com. Please find the free models here: https://www.printables.com/model/374780-playseat-challenge-mount-for-diy-sequential-shifte ___ Same thing as the original, just with the bolt pattern for the DIY Sequential Shifter bbeavis.

### Installation: V3:   Install ZipTies in mounts   Install rear pedal mounts with M6 Bolt and washer   Option A:     Remove the footplate (3x Red bolts)     Install front mounts   Option B: (Requires 1mm Wrench)     Install front mounts with the...

A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ... More Information:...

Use this universal mount to proper secure things to a playseat challenge, or other things with 25mm tube diameter.I used it to mount the power-supply. ... Hardware needed: 2x M4x30 Screw 2x Washer for M4 2x M4 nut

Clear the wheel mount tubing latch The outside mount and surface are in 2 pieces for a couple reasons: 1. Can hopefully be printed on printers with a smaller build volume. If it were a one-piece assembly, it would not fit on the print bed of my Qidi...

This universal mount is designed for the Playseat Challenge. The mount was originally designed for the shifter plate from Advanced Sim Racing. But it can be used for any custom design. The spacing between the mounting holes is 85.2mm. Hardwares: ...

Universal Playseat Challenge Fanatec Pedals MountsAfter breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. ...This universal mount allows you to affix both Fanatec V3...

Recently purchased the Fanatec CSL DD Wheel & CSL Pedals combo intending to mount on my Playseat Challenge. The wheelbase mounted fine, but the pedals had no good way to mount rigidly other than the large velcro strap that comes with the Playseat. ...

Because I had problems to slice the floano's version I made this version myself. I had some test versions, but those broke down after hard gear changes. This is somewhat more robust version that should last longer. I personally can't figure out...

Mounting bracket for PlaySeat Challenge. Made it for mounting Fanatec shifter. The white plate on picture is for mounting Heusinkveld Sequentil shifter. They can be used for mounting all other plates and accessories. Mounting hole is 6mm, you need...

This model utilizes the remaining hex cap bolts from my Playseat Challenge which makes it a "no hardware" design with the assumption that you kept spare hardware post installation. There are a total of six printed parts. Four latch on to the frame...

I really liked jeoje's design for the Playseat Challenge, but I didn't have any M3 hardware that was long enough. I had some M6x40mm flat head screws leftover from another project, so I decided to use those instead. I started from scratch using...

I really liked jeoje's design for the Playseat Challenge, but I didn't have any M3 hardware that was long enough. I had some M6x40mm flat head screws leftover from another project, so I decided to use those instead.</p> <p>I started from scratch...

This is a pretty crude remix of the awesome playseat shifter mount by jeoje. I combined the outside bracket and the shifter mount plate into one piece. I reduced the thickness of the mounting plate and added holes for the TH8a bolt pattern. I also...

The remix of fr3zno is very decent! ... The corners of the mount were a bit sharp so I made a small modification by smoothing the corners. ...

This is a remixed Version of Jeoje's Playseat Challenge Shifter Mount for the Thrustmaster TH8A. It is similar to CorrieD's Version with some improvements. #####Thanks to Jeoje for this awesome design and for providing the source files! The...

Modified the fanatec pedal adapter and used it completely differently and modified for the MOZA SR-P pedals A lot of holes because my legs are short and even on the closest setting the pedals were not at a comfortable place The pebbles are here to...

Modified the fanatec pedal adapter and used it completely differently and modified for the MOZA SR-P pedalsA lot of holes because my legs are short and even on the closest setting the pedals were not at a comfortable placeThe pebbles are here to...

I also recommend adding one wrap of grip tape to the circumference of the tubing frame of the chair to ensure your mount doesn’t rotate when you shift into reverse. This is printed from PLA filament and only requires a 20% infill for structural...

This is the mount made by jeoje, but I merged the right side of the clamp and the flat surface in one piece. I printed with tree supports and blocked the supports for the holes on the big piece. ... Holes for Logitech shifter.

Just trying to design a mount strong and eazy to print and mount as possible.main part is redesign from "Playseat Challenge Shifter Mount" by jeoje" Drawback: The plastic pad latch(which you open every time you leave the seat),only can open from...

Be warned - You take sole responsibility for any damage to your Fanatec Shifter, Playseat Challenge chair, 3D printer and anything else by using this design. I won't take any responsibility for this home-made design! ... In the unlikely event of anyone...

Here's a mount I designed that allows you to install a 25mm bar onto the leg frames (front or back) of a Playseat Challenge. I used this to attach my own Bass Shaker to my Playseat Challenge. ... Here's a 3 part video on how I did that showing the...

A shifter mount for mounting Logitech shifters onto the Playseat Challenge racing rig. Logitech-playseat01 is the shifter mount for mounting on the right side Logitech-playseat02 is the clamp for mounting on the right side and Logitech-playseat03 is...

Universal mount for button box. Add a hole on the box side. You might want to use glue for the box & a rotary to keep the placement. ... - 5x M3 - 5x M3 Nut