quest 2 golf club 3d models
961687 3d models found related to quest 2 golf club.
thingiverse
This extension allows to attach your Quest 2 controllers to a real golf shaft. Get you hands on some old putter or other club and cut the shaft in half. Now you can fasten the printed part to the shaft with 2 nuts and bolts. Alternatively you could...
thingiverse
"Quest_Golf_Adapter_JSD_v2.stl" Is the same as above, you can see I change it up some. Either one works fine, not sure one is really better than the other. V2 has more plastic so may be a bit stronger, but weigh more. Used M3x40mm bolts because...
thingiverse
An adapter to glue a broken old shaft (or a cut new one) and grip together which works in the Golf+ app for the Oculus QUest 2. Two velcro straps of 10 cm are required to mount the controller (left handed or right handed version). Can be...
thingiverse
Mount a right hand Oculus Quest controller to a Golf club shaft. This requires 4 screws/bolts ~M4 size and 32mm length. I used lock washers and wing nuts with the bolts as well as 2 6.5mm nylon spacers for the middle section of the clamp. The...
prusaprinters
... belt strap to secure your controller. ...You can get them here: https://sanlaki.shop/products/golf-club-diy-kit Walkabout Minigolf - set angle to 38Golf+ - use Sanlaki preset (currently broken, working with devs to get the alignment sorted out)
thingiverse
Quest 2 Golf Club adapter for a real golf club. I love Walkabout Minigolf and Golf+ on the Quest and this adapter adds a lot of realism to both games. This is a strong adapter, you can do a full swing without worrying about your controller...
thingiverse
...It’s a Remix of the Extended Golf Handle - Quest 2 If you want to make the angles perfect here is the public Tinkercad, be my guest just post it when you do. I think angles are OK as they are now. ... https://www.tinkercad.com/things/dyvYMRbhQtg
thingiverse
This mod holds the quest 2 controller secure at the end of a cut down club. Adjustable weight improves swing realism. What you need: Donor club with stepped shaft 12.5mm (1/2") at the cut end. A tapered shaft will work but will require more effort...
prusaprinters
This mod holds the quest 2 controller secure at the end of a cut down club. Adjustable weight improves swing realism.What you need:Donor club with stepped shaft 12.5mm (1/2") at the cut end. A tapered shaft will work but will require more...
thingiverse
This is my version of a golf attatchment made specifically for my Oculus Quest 2! I tried to make the design as similar to Deadeye VR's product as possible. So instead of spending $70 I only spent $10! The controller should fit inside the print very...
thingiverse
For putting / golf games on Quest2 Because this uses the original controller orientation it seems to work fine without needing pre calibration for specific grip models, which is as of today is not supported in the games I use. Gripping lower on...
thingiverse
I found the best success with the "CUSTOM" club in the golf+ settings and aligning the remote onscreen with the actual location of the remote on the golf club handle in real life. The dead eye works but custom seems better. The picture shows using...
3docean
3D model of Golf club.Object are grouped Rendering. materials are Included and detailed with all files. For any problems please feel free to contact me. ... Don’t forget to Rate and enjoy!
thingiverse
This is a remix of https://www.thingiverse.com/thing:5204772. ... I needed to make it a bit stronger as it broke off at one point. There are also 2 different versions, 13.5 and 14.5 shaft diameter.
thingiverse
Added a why for the wrist strap to come out so it doesn't need to be removed
thingiverse
This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...
thingiverse
This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...
thingiverse
A mini driver to make a kids golf club. Head size is 3" wide, 2-1/2" long, 1-3/4" deep. ... Not including the hosel.
thingiverse
This is part 2 of my attempt to create a golf club for my classroom. It uses a 3/8 thick wooden dowel. ... I printed it on TPU.
thingiverse
A 3d printable golf club and ball so you can give it to that person that loves golf
prusaprinters
This is a pencil holder in the shape of a golf club where the pencil is the handle of the golf club.
thingiverse
A simple design of a stand for a Keep Sake item. ...The "My First Golf Club"
grabcad
GOLF CLUB SHAFT GAUGEA SIMPLE TOOL USED TO MEASURE THE OUTSIDE AND INSIDE DIAMETER (=WALL THICKNESS) OF STANDARD CLUB SHAFTS AND THE RECEIVING HOLE IN THE CLUB HEAD WHEN BUILDING/FITTING GOLF CLUBS. ...CENTER HOLE IS 1.680IN DIAMETER TO CHECK GOLF...