ratchet clamps 3d models

This version is based on my print-in-place ratchet clamp (https://www.myminifactory.com/object/3d-print-89776). I use this clamps for small woodworking projects. This time is printed in two parts (to avoid welding while printing) with minor...

This is a customizable replacement foot for a ratchet clamp. ... The default settings fit a Grip ratcheting bar clamp.

... ...works best on thinner surfaces. To assemble insert the ratchet clamp into the hole in the top of the tub so the short spur can interlock with the rack on the back of the tub. ...Finally use the wedge to fill the gap between the clamp and the tub.

This is a small ratchet clamp, design to print in place. It can be scaled up, tested at 200% original size. ... Printed in PETG, 0,2mm resolution, 40% infill.

... the pieces welded.   This is a mini ratchet clamp, design to print in place. It can be scaled up, tested at 150% original size (the green one in the photos is original size, white one is 150%). ... Printed in ABS, 0,2mm resolution, 40% infill.

Inspired by the ratchet style pipe clamps here is my take on the NASA CHAMP project. The clamp has been designed to flex open to fit around the hand rail. Once in position the clamp is closed and locked in place with the "teeth" on either face of...

For the ratchet part I added a stl file with a support offset by 0.3mm to facilitate printing (to be printed without additional support). The two parts to be glued are the circular spring inside the knob and the pattern on the top of the knob that...

For the ratchet part I added a stl file with a support offset by 0.3mm to facilitate printing (to be printed without additional support). The two parts to be glued are the circular spring inside the knob and the pattern on the top of the knob...

Paper roll holder for ratchet clamps to hold up seamless background. ...I used harbor freight clamps with rod size 6mmx16mm and paper roll is 30" wide 20mm inner diameter.

I hate supports so I tried my best to come up with a design that doesn't utilize supports, yet retains the functionality of this ratchet cable clamp, but I couldn't. However, after several iterations I believe I've come up with a design that works...

I wanted to print a smaller version of the ratcheting clamp and I thought that the original was too thin to be scaled. Plus I tend to make things a bit overdesigned for long lasting durability and stregnth. Additionally, I wanted to assemble it...

I took the Molette.stl and modified the outer edge to have larger grip points to make it easier for my printer.

“Ratcheting” is perhaps not exactly the correct term for this, but the design does allow for the clamp handle to be moved without moving the clamping screw. This is a simpler version of commercially available clamping levers. The cheapest clamping...

Fits the older style trigger-type ratcheting clamps from Harbor Freight. These clamps were mostly black with flourescent orange pads. On those models, the trigger was towards your palm rather than your fingers. Sorry, can't find any model numbers as...

I swear everyone of these Harbor Freight Ratcheting Clamps internal handles/triggers are different. There are numerous ones out there, but none seemed to be the right size so I designed my own.  To complicate it, the inside pin on one side also...

Customized version of https://www.thingiverse.com/thing:3101465 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3101465

Customized version of https://www.thingiverse.com/thing:3101465 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3101465

This is another print-in-place experiment. It can be scaled up, tested at 150% original size (the green one in the photos is original size, white one is 150%). ... Printed in ABS, 0,2mm resolution, 40% infill.

These tiny ratcheting cable clamps may help you to store your tangling cables properly. Middle size version is good for power & thicker USB cables, while the small version was designed especially for thin headphone cables.Update #20160403: I have...

There are 3 different edge clamps in this file. ... One for a Triangle (60°) One for a Square (90°) One for a Pentagon (108°)

... printer. ...Not sure who manufacture it because i see this one a lot rebranded over eBay. May this model can help someone anyway, looks like i'm not the only guy who had this problem: http://softsolder.com/2011/11/04/harbor-freight-bar-clamp-failure/

... printer. ...Not sure who manufacture it because i see this one a lot rebranded over eBay. May this model can help someone anyway, looks like i'm not the only guy who had this problem: http://softsolder.com/2011/11/04/harbor-freight-bar-clamp-failure/

I broke my cheap clamp and tried to make simpler replacement part, that is easy to print without supports. ...It works well, but I will see how long it will last.

Assembly: -Press fit the spring arm into the main body (the main body has some nubs sticking out to hold the spring arm) -Push the ratchet arm onto the axle of the main body -Put a dab of glue on top of the spring arm and then glue on the other body...

... parts. Works in PLA or ABS. Inspired by traditional cable clamps like this one: https://amzn.to/2HLJeTN Update: Here is a modified version by 'robkingva' which allows you to snap the parts together! ...http://www.thingiverse.com/thing:715328

This is a simple clamp for holding bundles of wires, cables, or even pneumatic hose. Edit: Here is a modified version by 'robkingva' which allows you to snap the parts together! ...http://www.thingiverse.com/thing:715328

This is a simple clamp for holding bundles of wires, cables, or even pneumatic hose. ...Edit: Here is a modified version by 'robkingva' which allows you to snap the parts together! 

Inspired by traditional cable clamps like this one: https://amzn.to/2HLJeTN Update: Here is a modified version by 'robkingva' which allows you to snap the parts together!http://www.thingiverse.com/thing:715328 Instructions I printed in abs at 20%...

I've always thought these clamps are cool for some reason, and I'm also working on a customizable version. The design is a little tricky though since the circles are all "unwrapped" when in the neutral position. Anyway, have fun with my scan if...

Summary I've always thought these clamps are cool for some reason, and I'm also working on a customizable version. The design is a little tricky though since the circles are all "unwrapped" when in the neutral position. Anyway, have fun with my scan...