rc magnetic body mounts 3d models

rc magnetic body mount 6mm

this is front and rear magnetic rc body mount for rc car, it has been made for sakura d4, but it can be fixed i other chasis

Made this to use the existing mounting holes and mounting brackets on one of my crawlers..The posts are 6mm with 2.5mm holes @ approx 6mm on center. magnets used are 10m x 25mm x 3mm... ... printed in petg 100% infill 5-18-23 added round version for...

Magnetic Body Mount for RC Drift Car / Race Car

I wasn't too fond of the idea of gluing or epoxying magnets to the body of my RC so I decided to develop a cleaner, simpler, quicker, less permanent & less destructive way to mount them. Tips: 1.) PRINT @ 100% INFILL 2.) You will need (1) 15mm x...

&nbsp;&nbsp;You will also need 12mmx3mm magnets, and some 1.5mmx15mm screws to attach it.&nbsp;It is designed for the screw to go through the factory body mount (to allow for adjustability). &nbsp;The magnets press-fit into the bottom. &nbsp;</p><p>I...

# RC Guided Magnetic Body Mount Just drop the RC Body over chassis, and voila! Mount RC Body has never been so easy! Just place a piece of double-sided tape in the RC Body to fix the magnectic and this thing. Please see the pictures for more...

90 deg adapter for RC car magnetic mount, made for MST RMX 2.0 it will move the magnet to trunk, so you don't stick the magnetic on the back window. ... It has 2 holes for height adjustment, and mounting the original poles from top or bottom for more...

Some quick magnet holders to hold RC drift bodies on to chassis with magnets nothing flash but helps retain the body when you clip the track barriers side ways.2 versions V2 has slightly deaper edges to retain the body better.Can be seen here:&nbsp;

Clippless magnetic body mounting system for 1/10 RC. No more holes and sticking poles from the body. You will need: -Magnets -14 M3 screws -washers (optional, for adjusting the mount width) Added a washer STL to save you a trip to the hardware...

Created this to allow the shell of RC vehicles to be held on magnetically rather than having to drill through and use clips.

... Información del mod https://cet3d.top/proto36-rc-car-posts/proto36-body-mounts/ Información general https://cet3d.top/proto36-rc-car-posts/proto36-rc-car-informacion/ Vídeo de presentación del proyecto https://www.youtube.com/watch?v=L1OxX1gPcJw

RC body rear magnetic mount (for HPI 1/10 RS4 RTR).

One piece RC body mount. Fits 15mm circular magnet and 5.5mm to 6mm posts. ...Easy to print.

One piece RC body mount. Fits 15mm circular magnet and 5.5mm to 6mm posts. Easy to print. ...

Magnetic body mount for 15mm circular magnets. Easy to print, I recommend choosing a strong material to make these mounts more durable. Not recommended for "bashing" or extremely rough driving/jumping, these are best suited for scale crawlers/trail...

Magnetic body mount for 15mm circular magnets. Easy to print, I recommend choosing a strong material to make these mounts more durable. Not recommended for "bashing" or extremely rough driving/jumping, these are best suited for scale crawlers/trail...

Magnetic mounts for the body are designed for a magnet with a size of 10x1mm. The magnet is pressed into the mounting head before assembly. For a better entry of the magnet, the head can be heated for a short time with a hair dryer. Support...

These mounts will work to attach an Axial SCX24 Jeep Gladiator body to the Traxxas TRX4m. They fit between the stock shock mounts using 16mmx2.5mm hardware. Four 5/16" x1/8" rare earth magnets were used. ShoeGoo was used to attach the upper plates to...

This is a since screw body mount for 70mm width chassis and could be adapted to something like a Gspeed chassis as well. The sides are meant to press in an M3 heat insert inside. An M3 cap head screw is meant to act as a body post. ...You can use a nut...

Made a universal magnetic holder for RC bodies which adapts a little bit to the contour of the body. Post diameter is 6mm. You'll need: 4x M3x6 screws 4x M3 nuts 8x small & flat magnets (mine have diameter of 10mm) I included a shorty version for...

This thing replaces the stock body posts and cross members on the Tamiya Bullhead with parts to mount the body with magnets. You're going to need a 2.5mm and 3mm drill bit as the front body parts need 2 additional holes each. Also there's 2 types...

I made a custom body for my SCX24 and needed a way to mount it. These mounts accept 6mm x 3mm magnets. I used these: https://smile.amazon.com/gp/product/B077K364Z7/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 The body I made had to be...

Love my Venom Gambler, but always hated the body mounts were soft and too flexible. Decided to re-draw them, very basic, but I feel a better heavy-duty version. ... I also decided to re-do the posts as well, just so it is a complete set up.

Love my Venom Gambler, but always hated the body mounts were soft and too flexible. Decided to re-draw them, very basic, but I feel a better heavy-duty version. ... I also decided to re-do the posts as well, just so it is a complete set up.

Adjustable mounts for Traxxas Tmaxx, 3 peices design allows you to position magnet correctly on any shape body. Uses M3 nut and bolt. 10mm magnets. ... Print main part with large brim, has a tendancy to get knocked loose jumping between towers.

I was facing a problem when trying to mount my new body and decided to come up with a solution that would move the magnets towards the rear. These are a low profile design with flush magnet mounts, and is sturdy upon impact. I am inlcuding 2...

RC Magnetic Post Mounts for RC Drift Car. Made for a Sakura D5. Front one uses micro screws. Rear one uses standard M3 screws. They can be used with each other, part are inter-compatible. Made to be used with 3x10mm round magnets. If used,...

This model has different ways to be assambled , depends of your chassie . Very impoprtant is to redril all holes to avoid breakage. ... Stick the velcro with hot silicon

body mount set to join hsp rgt chassis to loops rc lc90/ bundera cab and body