rmrc mini recruit manual 3d models
141485 3d models found related to rmrc mini recruit manual.thingiverse
Split scimitar winglet replacement for the ReadyMadeRC Mini Recruit / Sonicmodell Mini AR Wing. Flies well. The curve is matched to the wingtip airfoil. Stays on well in landing with just hot glue. ...Probably way less efficient because of added weight...
thingiverse
This is a motor mount adapter for an 1806 motor with 12x12mm M3 screw hole pattern, intended for motors such as the Brotherhobby 1806. ...Screw heads are properly countersunk. Reuse wood screws that came with the Recruit Mini.
cults3d
nose weight for the RMRC recruit v2 wing adjust infill to achieve desired weight
thingiverse
nose weight for the RMRC recruit v2 wing adjust infill to achieve desired weight
thingiverse
Replacement nose for RMRC Recruit. I printed 0.25mm Layer Height and 0% infill. ... Weight is approx 32g.
thingiverse
If you have managed to crash your RMRC Recruit, you'll probably need to be replacing the winglets. Instead of having to buy a partial wing replacement to acquire the appropriate winglet, just print mine. The design is slightly more streamlined,...
youmagine
I needed an antenna mount for my Recruit, and thought others may need too. ... I printed mine out of TPU (Filiflex actualy) so it has a little bounce which should (and has) prevented damage to VTX.
thingiverse
This clicks into the exhaust port on the rear of the RMRC Recruit mini (Or AR Wing from BG) to house your Foxeer Lollipop 2 antenna. ...It has a hole going through the entire piece to allow the exhaust port to function normally, just make sure to place...
thingiverse
RMRC Recruit / AR Wing Battery Tray. ... Stronger/better than original wooden one.
cults3d
RMRC Recruit / AR Wing Battery Tray. ... Stronger/better than original wooden one.
thingiverse
Remix of the RMRC Recruit VTX/FC/GPS mount by e2p2 except I shrunk down the mid section to 24x24 to fit the Matek F411 Wing FC. ...
thingiverse
This is a mount similar to the wooden kit that comes with the RMRC Recruit to mount a Caddx Orca. The Strap holes are sized appropriately to fit the straps included with the Recruit. ...
thingiverse
This is a mount for the RMRC Recruit to fit a Insta360 One in the space were a go pro would fit. The Lid and the front cowling need to be modified to fit this Thing. Also the lid handle tab should be reinforced so as to not pull it out on a hard...
thingiverse
This is a quick design for a RMRC Recruit. It holds a Matek VTX-HV, just about any 30.5x30.5 FC, and a micro GPS unit. The FC and VTX are on the same level so the usb plug is blocked. You may want to use some standoffs to raise the FC so the usb...
prusaprinters
This is a quick design for a RMRC Recruit. It holds a Matek VTX-HV, just about any 30.5x30.5 FC, and a micro GPS unit. The FC and VTX are on the same level so the usb plug is blocked. You may want to use some standoffs to raise the FC so the usb port...
thingiverse
This will hold your FRSky X8R Antenna on your Recruit v2. It is much better for reception if you can have at least one antenna vertical. It has holes for mini zip ties. I would HIGHLY recommend also using double sided mounting tape. You can...
thingiverse
This will hold your FRSky L9R Antenna on your Recruit v2. It is much better for reception if you can have at least one antenna vertical. It has holes for mini zip ties. I would HIGHLY recommend also using double sided mounting tape. You can...
thingiverse
I designed a this mount for the Insta360 One X (or potentially the One) to hang off the front of the ReadyMadeRC Recruit. Its designed to be printed in PLA. It includes its own 1/4” thread, which is the designed failure point in the event of a crash...
youmagine
Print in your favorite media and mount that Pixfalcon boi!
thingiverse
1/8 THICK WINGLETS PREFERED MATERIAL WOULD BE ABS! I've kept winglet geometry to spec (identical to factory shape only thinner) all edges are rounded for smooth airflow. NOTE!!! THIS IS DRAWN IN INCH FORMAT.... YOU MAY NEED CONVERT SIZE IN...
cults3d
Motor Mount & Led Holder for the Sonicmodel 900 Wing. This thing is my Mashup of mycopter's AR Wing 900 Motor Mount & dre77's LED Halter fur AR Wing. ...Works with motors with 16x16mm mounting.
thingiverse
Motor Mount & Led Holder for the Sonicmodel 900 Wing. This thing is my Mashup of mycopter's AR Wing 900 Motor Mount & dre77's LED Halter fur AR Wing. Works with motors with 16x16mm mounting. ...
thingiverse
Order pre-made in resin from my site: https://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/
prusaprinters
Order pre-made in resin from my site: https://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/ Category: R/C Vehicles
thingiverse
Caddx Turtle V2 mount for the RMRC Recruit or AR Wing. Simply mount in front HD camera area, I used 3M VHB tape to secure the mount but you could also glue it in. Use the caddx screws to secure the dvr board to the 4 post mount and cam to backing...
thingiverse
... into the height). Inspired by excellent concept design by harkal. You can purchase this pre-made on a liquid-resin stereo lithography printer from my webstore: http://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/
thingiverse
This is a simple compact combo (FC GPS VTX ESC) tray for RMRC Recruit and AR Wing 900. I designed the tray specifically for the F-35 FC & GPS, Holybro ATLATL V2 and stock 30A esc. Will also work with standard 30.5x30.5 boards. Recommend using...
cults3d
... into the height). Inspired by excellent concept design by harkal. You can purchase this pre-made on a liquid-resin stereo lithography printer from my webstore: http://www.matter-replicator.com/product/ar900-rmrc-recruit-dji-fpv-air-unit-mount/