rsa token download 3d models
134793 3d models found related to rsa token download.thingiverse
This is a custom stand made to fit an RSA SecurID token which is attached to a lanyard. ...It takes about 35 minutes to print.
thingiverse
The Double RSA Token Holder sits on your desk and holds two RSA tokens for easy reference. It also travels relatively well. ...The tokens are held in place by gravity and have a slight slant away from the tether ring to make them less susceptible to...
thingiverse
I really like the badge holder design but also needed a carrier for my security RSA token so I modified to add the token "keyhole". ... Works great to cleanly keep the token and badge together.
thingiverse
... the noise down while walking. As can be seen in the photo, the RSA dongle still uses its own method of secure attachment, and the plastic restraint remains in place when clipped inside the snap strap, with or without the RSA token in place. ...
prusaprinters
A stand to hold up to two RSA SecurID tokens. Print instructionsExample printed in Fillamentum Wizard's Voodoo PLA. ..."0.20mm Quality MK3" setting in Prusa Slicer.</p> <p>Should print easily with pretty much any settings.</p>
thingiverse
Printed standing on its RSA bottom upright (tall) with no supports. Just a hint of "sag" on the final edge. it was so little, I probably wont correct it. if I do I'll upload. Printing upright took 7.5 hours but I was able to print several at a time...
thingiverse
This is a new version of my RSA Clip that attaches to the lanyard vs. the badge. I like my lanyard to sit higher on my chest when I use a retractor, so the clip is designed to allow the lanyard to be double wrapped to take up slack. If you don't...
thingiverse
Used to clip an RSA SecurID token to the lower bezel of a computer display.
thingiverse
This holds two RSA tokens securely. ...There are lanyard slots on the back.
thingiverse
Holds up to a 64mm by 90mm badge and RSA token on the back, printed with supports for the top bridge. Uses a 6-32 ? ...screw for the RSA token but it friction fits pretty well already.
thingiverse
It will hold two RSA tokens back to back. I added more bevels to the 2.1 version. It fits better to the round part of the token. It is a tight fit and will not slip out once two token are inserted. ...V2.1 STL file is also in the correct orientation for...
prusaprinters
I wanted a way to keep my RSA token with my security badges for work, and this was a good opportunity to grow some simple TinkerCAD skills. ...There's a satisfying snap when you pop the RSA token into place the first couple of times. (I'll add some...
cults3d
added more material between badge holder and rsa token holder for better structural integrity scale down to 10% in slicer (I misnamed this one as the "Do It Again!" one - that one is now in the remixes section)
thingiverse
added more material between badge holder and rsa token holder for better structural integrity scale down to 10% in slicer (I misnamed this one as the "Do It Again!" one - that one is now in the remixes section)
thingiverse
RSA token holder. ... Changelog: v0.1 - initial draft v0.2 - higher stand; tighter fit Print Settings Printer: Wilson II Rafts: ...
thingiverse
Print between 10% to 20% infill. ...This holds two standard RSA tokens on a lanyard and acts like a bolo tie. ... v2 has slightly larger (2mm x 20mm) lanyard slots with a 7mm wide opening for thicker lanyards.
prusaprinters
added more material between badge holder and rsa token holder for better structural integrity11/09/22: this one should be the right sizeCategory: Office
thingiverse
Gets lots of compliments from coworkers who are tired of hearing their badge click against their RSA tokens while walking. Uses 4x M4x12 or longer screws Updated 17 Jun 2018: Uploaded the v4 of the front and back, this version doesn't require...
thingiverse
This is a clip-on holder for an RSA Token. The original design fits a two sided badge holder, but you should be able to customize it to fit single sided holders by adjusting the badge_width variable. If you print the clip on it's edge, it...
thingiverse
I got tired of the RSA token bouncing around on my lanyard, so made a holder for it that fits a standard badge holder. Perfect for double sided badge holders. ... Fit is pretty snug, so it sits flush and doesn't bounce around
thingiverse
This is a remix of timbo's ID Card and RSA Token Holder. I changed the width to hold a single ID card for work. It took me several tries to print with acceptable results... probably because I fileted all of the edges to make it smooth. The final...
thingiverse
This is a remix of Gizmoticist's excellent RSA SecurID Stand.http://www.thingiverse.com/thing:343057 My company requires use of SecurID tokens to log into their services. These require a lot of data entry to authenticate and now you have to log in...
thingiverse
Clip for holding RSA key above monitor. ...Very handy if you frequently have to type your credentials in for telework.
thingiverse
For your two-factor RSA token needs. If you use the loop built into the token, it's mass causes it to "bounce" noisily, and if you hit a harmonic in your walking it can start swinging. This is to hold it more securely on the lanyard itself. A...
thingiverse
ID Card and RSA Token Holder for two RSA SecurID tags. ... https://amzn.to/38KGRK6
thingiverse
Holds 2 RSA tokens, a print (tear shaped) token and 2 credit card size badges.
thingiverse
Holds 2 RSA tokens, a print token(tear shaped token) and 2 credit card size badges. ...Print token should work through the back of the holder.
thingiverse
Hold two RSA tokens on your lanyard in a single V-shaped holder. ...I got tired of my two separate RSA token holders moving around, sliding into each other, twisting, etc. ...This holder prevents all that.
thingiverse
It should be noted that the intended use is to have the RSA token inserted upside down so that it can be read by the wearer. this means the circular portion of the RSA token would be on the wears left. ... https://youtu.be/ORPBSBKY060 ...