sand paddles 3d models
46878 3d models found related to sand paddles.thingiverse
This is a rim and a sand paddle tire for a 1/10th scale RC car. Uses a standard 12mm hex nut in the rim that is on most common RC cars. The rim I'm printing in ABS and the wheel will be in TPU, I will add pictures when both are finished and...
myminifactory
Printable paddle tires compatible with Traxxas 2wd vehicles. REQUIRES NO GLUE FOR THE TIRES there are "locking lugs" on both wheel and tire to keep it from rotating on the wheel. (6) 3x12mm screws are required to assemble wheels. These smooth...
thingiverse
This is the same paddle design as the original but the hub has been moved closer to the center of the wheel and has been made larger to fit on a 1/8 scale. ...Inner diameter =75mm
thingiverse
You can open the model for these paddles in Thingiverse Customizer or in OpenSCAD customizer to configure your wheels: **Attention**: In customizer, always use the dot "." for decimal numbers, not the comma! **General Section** * What to print: you...
cults3d
Snow/Sand paddle tires for the Losi SBR 2.0, but would probably work on other cars with a 17mm hex. ... The tire gets screwed on the rim, you will need for 1 wheel assembly : 10x M3x 16mm 10x M3x 20mm Video in snow : ...
thingiverse
Customized version of https://www.thingiverse.com/thing:3571847 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3571847
thingiverse
Customized version of https://www.thingiverse.com/thing:3571847 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3571847
thingiverse
Customized version of https://www.thingiverse.com/thing:3571847 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3571847
cults3d
... and makes this thing very heavy XD Here' s a small video where you can see it in action. ... https://youtu.be/mfZLuc1Wytw PS : printed the tire in TPU 95A, works but gets instant rigid in the cold and the paddles break off....so your choise ;)
thingiverse
This is a remix of the openrc winter fun tires. ... I added support material and it reliably prints with no need for other support.
thingiverse
These are micro sand tires combined with a 7-spoke beadlock style wheel for 1/36 Losi or 1/32 JJRC LT832 cars. I recommend printing it with the outside facing up for best results. ...You will likely need to file/sand them for proper fitment.
thingiverse
This is my solid wheel for use on soft sand. Right Hand side only. Flip in your slicer to get the Left side version. All solid (but hollow out to around 2mm in your slicer settings). 12mm Hex drive. Designed for my Stadium Thunder but will fit many...
prusaprinters
Controllable and good power with regular tires up front and paddles on the back. Small issues: the inside rubs a bit. Nothing a little chamfer on the inside edge shouldn't fix. The hex is also a bit snug. Could probably just print the whole thing...
cults3d
Wheels for sand, snow or hydroplaning, HEX17mm
thingiverse
This was designed for a Monster Slash conversion but will fit on basically any 12mm hex vehicle given the dimensions are fit.The tyre is supposed to press fit or be glued to the wheel. ...Please inform me if any mounting or design error occurs.
cults3d
This was designed for a Monster Slash conversion but will fit on basically any 12mm hex vehicle given the dimensions are fit.The tyre is supposed to press fit or be glued to the wheel. ...Please inform me if any mounting or design error occurs.
thingiverse
This is a paddle tire for snow and sand on a 1/8 scale rc truggy. 155m diameter, 60mm wide for 17mm hex With a little bit of force you can push the tire over the rim so it is form fitting connected. You can additional use some glue, too. ... ...
cults3d
A collection of spanking paddles I have made. ...The edges are a tad sharp I recommend sanding them well before heavy use
sketchfab
A basic sand texture that includes Basecolor, Roughness, Normal, and Height maps. ...I’m currently focussing my efforts on substance designer.
3docean
This is a set of 4 hand painted sand textures, all tiling. ...Each one is a flat PNG at 512×512