scope adaptor for iphone 3d models
2322159 3d models found related to scope adaptor for iphone.thingiverse
this was made for my iphone 5 and a swarovski spotting scope with a 55mm eye piece, i plan on plastidiping the ring on this after printing to protect the scope and givr it some grip
thingiverse
Vixen-style dovetail adaptor for finder scope. An M4 nut is needed for the lockscrew. The nut is tight fit, it can be slowly pulled in the hole with an M4 screw (after printing of course). I printed mine in PETG, 4-5 perimeters and 20% gyroid...
thingiverse
I have added an STL to adapt the Celestron Red dot finder to fit my finder scope adaptor and any Skywatcher finder scope shoe. Instructions I printed it at .2mm layer height, with 10% infill. ...
thingiverse
... need the screw. I have other things for my telescope to take a look: A solar Finder: (be carefull to not look to the sun without a solar filter) http://www.thingiverse.com/thing:1066006 A camera adaptor: http://www.thingiverse.com/thing:1033792
thingiverse
... screen. ...It's also a handy charging station and de-clutters your desk! Instructions I suggest you use a 'raft' and also tick 'support' for the SD card adaptor on the Replicator 2. ...Thanks to MakerBobDesigns for providing the blank iPhone case!
thingiverse
It was designed for a Hawke Eclipse 6-24x50 SF IR scope. the ocular bell diameter is 43mm with an Eye Relief of 96.5 there for this mount has a 44.5mm inner diameter and adjustable lens distance. The iPhone XS max camera is not round rather oblique...
thingiverse
Adaptor to allow use of Explore Scientific finder scope on Orion finder mount. ...I was unable to use the nice Explore Scientific finder scope after upgrading the Explore Scientific focuser to a Moonlite Nitecrawler so I made this conversion fitting.
thingiverse
Designed in Tinkercad For mounting a Rifle Scope on a normal Tripod with Quick Mount Quick mount plate is 43x43 mm Scope Mount is 120mm long
thingiverse
This adaptor sleeve connects a small camera equipped with a 28mm barrel diameter CCTV lens to a Losmandy polar scope. No retaining screws are required. ...With a ZWO ASI120 camera a 6mm focal length lens works well - the 2.1mm wide angle lens supplied...
thingiverse
This adaptor sleeve connects a small camera equipped with a CCTV lens that has a barrel diameter of 28mm, to a polar scope that has a diameter of 30mm. No retaining screws are required. With a ZWO ASI120 camera a 6mm focal length lens works well -...
thingiverse
This is an Adaptor for a small telescope to be mounted onto the Lab Radar to enhance the target sighting. ...
thingiverse
A mount to attach an LG G4 smartphone to my spotter scope eyepiece to make it easier to take photos.
thingiverse
This is a iPhone 11 Pro Max mount for a tripod, this is a bit more wild so I don't have to remove the phone's case. ... I don't have much knowledge with 3D so the design is not that great, but it's working perfectly for me.
thingiverse
Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: No Supports: No Resolution: 0.04mm Infill: 10 Notes: printed on high quality in PLA 0.4mm on a slow speed of 60 mm/s @ 280 degrees heating the base to 60 degrees How I...
thingiverse
This is a holder for Samsung Galaxy S8 cell phone used on Praktica Hydan 25-75x90 spotting scope. Holder is made of two parts: S8 case itself and its spoting scope adaptor. Then these two parts are glued together by means of CA glue. Adaptor is...
thingiverse
It's been a little while since I needed a phone scope for my phone but after upgrading to the 8 and then a Xmax this year it was time to update my design. ...Pretty simple clamp design works with either 8 or 10s with slim cases and is printed in ABS...
cults3d
scope cam mount for iphone SE allows you to mount the iphone on a shooting scope
thingiverse
... if bumped. This adaptor enables a 30pin-lightening adaptor to fit inside, and provide support for the iPhone 13. It fits in place of the stock Yamaha iPod adaptor plate. ... it is a nice tight fit to ensure that the iPhone is rigidly held.
prusaprinters
A larger guide scope is better in terms of fainter guide stars or a few 0,1"s better guiding accuracy, but this 30mm one is much smaller and lighter, and very affordable, especially if you need an extra, portable guide scope.The focal length of mine...
myminifactory
A simple adaptor that allows you to take the Svbony (non-name brand) Guide scope and attach it onto a Skywatcher tube ring using the screws that comes with both scopes. Here I've used 2 1/4 inch camera screws to clamp down, I recommend 20% infill...
thingiverse
This is an adaptor for mounting an SPC900 webcam to the polar scope of an EQ5 or EQ6 polar scope as seen on this video: https://www.youtube.com/watch?v=5L6IvfievRE Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill: 60% Notes: Printed it...
thingiverse
upgraded mount for renfert scope the pin is merely for testing fit...don't need this file
thingiverse
A simple pluggable adaptor for my passive iPhone 4 Brodit holder to use with a iPhone6. The slot for the phone is 9mm to use with a silicon case. You can customize this by self with OpenSCAD. ...Print Settings Rafts: Doesn't...
thingiverse
The scope has a very short backfocus, but with this adaptor it is possible to focus it at infinity with a ZWO planetary camera. A mini-Bahtinov mask is also included. Print it in PETG with variable layer height (or 0.1mm) beause of the fine...
cults3d
If you're like me and find getting your phone directly over the center in order to get it to charge is cumbersome, then this is for you. It automatically centers up your phone and helps keep it from falling off when you hit a bump. This was...
thingiverse
If you're like me and find getting your phone directly over the center in order to get it to charge is cumbersome, then this is for you. It automatically centers up your phone and helps keep it from falling off when you hit a bump. This was...
thingiverse
... off axis, so I decided to add a finder scope shoe to the top of the scope using the holes left by the vixen rail mounts. ...This adaptor allows me to mount my guide scope and camera to the front of the scope on the axis, balance is now not a problem.
thingiverse
This little adaptor is for keeping an Olloclip (which was made for the iPhone 4/4S) snug against an iPhone 5. ... Instructions Just slip the adaptor between the corner of your iPhone 5 and Olloclip.
cults3d
This is a dock adaptor for an iPhone 6. I used the guts from my iPhone 5 dock. ... This case will fit over the guts.
myminifactory
Remembering I have an old Gorillapod in my gig bag I thought I'd have a go at making a mounting frame for my iPhone 6 Plus. Seems to work pretty well so far! I recommend printing it on a high resolution and fairly solidly (50-80% fill) so it can...