scx10 ii forward motor mount 3d models

-Motor Mount Motor mount is designed around the original Axial Scx10/Wraith 3 gear transmission along with the original top shaft. This piece flips the motor 180 degrees. In order to use the motor mount your crawler must be running 3-link with pan...

I designed this piece to work with my trans and motor flip mounts for a 10.2 kit chassis. Steering servo in stock position and a servo winch flat and as low as can fit up front on the chassis. You may have to space your servo up depending on the...

Flip your 10 ii kit transmission and motor forwards for the best cg! The motor flip mount fits a good range of pinions, 10-14 at least, maybe a bit lower and higher. The motor mount is pretty solid as long as you print it pretty thick, 5+ walls,...

Flip your 10 ii kit transmission and motor forwards for the best cg! The motor flip mount fits a good range of pinions, 10-14 at least, maybe a bit lower and higher. The motor mount is pretty solid as long as you print it pretty thick, 5+ walls, I've...

The SCX10 Front Motor Mount will allow you to easily mount your motor and Axial stock transmission, on the nose of the SCX10 frame, and make tons of room in the center for a Transfer Case and Interior for your custom build.

Cross brace to allow for dual servos to be mounted. ... -Requires CMS -Requires battery relocation

second servo mount for scx10 ii to use a servo winch. ...I had to make the stand offs taller to accommodate the servo and spool.

Two mounts and a guide to bolt a standard sized servo converted to a winch in the Axial SCX10 ii frame. The servo goes behind the steering servo and uses all stock mounting holes. For best results use the second half of the clam shell factory cable...

I received a pair of scx10 ii ar44 axle housings, and I needed some link mounts for mockup.. I could not find any available so roughed out one in Tinkercad. They seem to fit pretty well but I don't expect them to hold up to serious crawling. ... This...

made a better place to mount a standard servo on the scx10 11 axle i have not printed it yet but i will soon but it should fit

A easy way to relocate your receiver closer to the center of the chassis. ...Requires an M3 countersunk screw and double sided servo tape to mount.

Motor flip mount for the original scx10 transmission, A little bit thicker in design then my 10.2 style flip mount but otherwise a similar design. Should also fit 10-14 pinion, maybe a bit more and a bit less. I also mirrored my trans when I flipped...

Motor flip mount for the original scx10 transmission, A little bit thicker in design then my 10.2 style flip mount but otherwise a similar design. Should also fit 10-14 pinion, maybe a bit more and a bit less. I also mirrored my trans when I flipped...

Heavy duty one piece servo mount plate for the Axial SCX10 II (AR44), INJORA, AUSTAR

Pivoting rear cage mount for the Axial Honcho rear cage. ...Fits both versions of the Honcho (SCX10 and SCX10.2).

Solid mounting of a (in this case towerpro mg) servo no. ...2 as servo winch or whatever. it's a one piece mount. All you need is the mount, 1 extra m3 screw for the mount and 4 screws for your second servo

This is a high bumper mount for the SCX 10 Honcho. ... It is printed best laying on its back.

Got a new set of Axels but on the front Axle there was no Servo Mount. I found an Idea on the Internet but had to customize it. It is mounted from behind the Pumpkin with 4 Screws. Here is another way to mount the Servo on the Axle.

After creating Version 1 I made a second one wich is mounted on top of the Axle. Here is Version 1. ...https://www.thingiverse.com/thing:2666675

MS composit Sfift II wing motor mount

I was looking on the Internet for a simple but working front motor mount. I found several but had I create one for HSP Gearbox. Here we go. Just screw it between the rails where the shock towers are used to be. With this setup It does not work...

This is a motor mount for Caliber II Trucks. ...Compatible with 5055 motor.

Bracket to place the car Axial SCX10 - SCX10 II on display

This rear battery mount area will fit a standard LiPo shorty pack  (25.5x47x95mm) and fits with the Ford 1956 F100 body in place. Please note that this is designed for the AX10 transmission. ...See the video below for installation prior to purchase. 

As i rebuild my SCX10 II Honcho, and made it longer, 335mm wheelbase. I needed longer driveshaft (Think its called WB8, Wildboar or something..) Recommend to glue the sleeve onto the axle at the center. 2 parts for better printing :). ...

I designed this stand for the SCX10 ii Honcho in mind. ...It supports the crawler a little bit to the front side so its more stable and doesnt tip over that easily (keeping in mind that the crawler is front heavy)

### Axial SCX10 ii Light Bar As it says on the tin, a light bar for the scx10ii. Fits in the roof rack that comes with the Cherokee. I fastened it on by using 3mm nuts and bolts. ... I've included support for both 5mm and 3mm LED's, both take 11...

This is a stand to support an Axial SCX10 ii under the chassis, (but will probably support other models). The stand is height adjustable by means of sliding supports. There are two different supports, offset for the front and centered for the rear,...

baca para crawler rc. ...especialmente para el axial scx10 2 k5 blazer pero se puede usar en el que quieras.

After designing some front motor mounts I was asked to make one that fits the Axial SCX10 frame. I made two versions. One for the stock shock towers and one for the shock towers I made (https://www.thingiverse.com/thing:3038608). They are called...