shop vac hose connector 3d models

Shop-Vac hose connector to use on my 10" MasterCraft Miter Saw and Shop-Vac 5 iterations all work with slightly different friction fit tolerances. ...I use #5, #1 the collar will snap off but is still usable even then

The coupler is a close fit and the ridge holds well, just start the hose rib on one side of the connector and work in the top. I installed on the second rib of the hose as it seems to make the most stable and secure connection. ...Link to a connector at...

A union conneector for a 1 - 1/4" shop vac hose to join two together. ...

This is the end cuff/end connector for shop-vac brand vacuum hoses. The locking tab takes some force to be pushed in, but can still be removed with a flathead screwdriver without damaging the locking tabs. ... This is compatible with 2 1/2" hose, with...

I used it for a shop-vac to put on a longer hose so I can leave the vacuum in the corner and clean everwhere. If your hose is of different dimensions, you can stretch or flip it accordingly. Staubsaugerschlauchverlängerung. Ich benutze dieses...

hole in shop vac hose so i cut designed fitting.either a little glue all around or like i did tape at joint

Replacement ShopVac hose end fitting for 2 inch nominal sized corrugated plastic hose. One fitting end has a single barb that fits into the cut end of the hose. The fitting is sized for a hose with a minimum actual ID size of 2 inches. I have a...

This is a hanger you can attach to your Shop Vac to wind\store your hose.

Coupler for [RIGID 2.5 Inch Vacuum Hose](https://www.homedepot.com/p/RIDGID-2-1-2-in-x-7-ft-Dual-Flex-Tug-A-Long-Locking-Vacuum-Hose-for-RIDGID-Wet-Dry-Shop-Vacuums-LA2520/305626325?MERCH=REC-_-pipsem-_-315749552-_-305626325-_-N) and [Shop-Vac...

This is an adapter to go from the 2.625" Shop-vac hose(one of the larger sizes) to the 2.25" Shop-vac hose.  Both ends of the adapter fit inside of each hose.  I printed this with PETG and with no support (small end down).

This is one of the parts made for my custom shop vac enclosure. ...This is the mount I used to connect my shop vac hose to my custom hose reel. ...The project can be seen on my YouTube channel: https://www.youtube.com/@makingofbrent

This is a Shop Vac Hose Adapter that I designed with a 2" OD on one end and a tapered 2.2"-2.4" OD on the other end. I bought a 20' shop vac hose from Home Depot and cut it in half. The cut ends were just the bare hose. The 2" end of the adapter...

I designed this adapter so I can connect my shop vac hose to the dust collection attachment on my Porter Cable sander. ... The actual inside diameter of this adapter is 31mm at one end and 55mm at the other end.

I have an old shop-vac that still runs great but the hose end had deteriorated. These are no longer available so I printed a new head which can be seen in the photos. ...Works great!

I foolishly backed over my old Craftsman shop vac hose and broke the end. I was surprised that I couldn't easily find a replacement, so behold. I believe it should fit your standard 2 1/2" hose for most vacs. Mine is an older model 16 gallon and I...

I recently upgraded my shop dust collection system from a shop vac with a 20ft hose (it got in the way all the time). Rather than buying new short hoses to reach each tool on the bench, I tried in vain to find 2-1/2" adapters for the hose but no...

Generic Shop Vac hose topper to help prevent the sucking up of pins or other smaller-ish items while allowing fibers, trimmings, and dirt to be removed. Print with the "mesh" side down on the build plate. ...No supports or infill needed.

Generic Shop Vac hose topper to help prevent the sucking up of pins or other smaller-ish items while allowing fibers, trimmings, and dirt to be removed. Print with the "mesh" side down on the build plate. ...No supports or infill needed.

I designed this to fit the Shop Vac and hold the hose with or without its extensions Instructions I printed it with a raft, vertical orientation: Material: ABS Infill: 10% Layer height: 0.27 Number of shells: 1 Feedrate: 80 mm/s Travel feedrate: 150...

I purchased a new shop vac and was greatly disappointed to learn there wasn't a swivel on the end of the hose where you place attachments so I created this one. It is designed for the standard 2.5" hose. Swivel is printed as three pieces. Cap goes...

If you would like to buy this hose and adapter, you can get it on Amazon here. Most power saws in the US have places to attach a 1.25" shop vac hose to keep the sawdust mess to a minimum. This is the weakest part and breaks. Even though mine...

shopvac hose adapter.. ...because yours broke

Basic hose adapter for 2 1/2" ShopVac Hose to 1" PVC hose. First make in Tinkercad so not the smoothest print. ... Print at 100% for correct size on Ender 3 Pro.

Bracket for snapping the shopvac hose into. ...Helpful for DIY CNC, used on my Shapeoko

It's fairly easy to push the hose in or pull it out but it stays firmly in place. It doesn't hold the hose tight once inserted. Helpful Tips: ALL filament shrinks after cooling. The amount of shrinkage depends on the type of filament. PLA...

My ShopVac hose wore out, and I went to buy a 10 footer so it would be easier to reach some things. They don't make one. So I bought two of the shorter ones, and built this coupler to tie them together. It works great for me. It might be...

Fits the standard Shop Vac hose connectors at 58mm. Mine were pretty snug. Only one 5 gallon bucket in the picture but I'll be adding a second one inverted with the bottoms cut out and taped together to increase capacity to about 7 gallons. That...

Made for my Rigid shop vac (2.5") to connect to my Saw Stop (4") dust collection port. ... Items needed: 4-5" hose clamp

A clip for 1-1/4 inch Shop-Vac hose to stop the join between two sections pulling apart when you yank on the hose. ...Just clips over the junction.

Hose nozzles with hanging clips for use with a 6 gal RIDGID shop vac, model 6000RV0. Each attachment is 5" tall and pressure fitted to the 1 7/8" hose. One nozzle is centered, while the other is off to one side. This should fit any shop vac hose of...