snapmaker enclosure 3d models

As a big Snapmaker fan I remodelled simplified 3D model of Snapmaker Enclosure .3D Printer and CNC and laser engraver is hereSnapmaker 3D Printer, CNC, Laser 200mW and 1600mWYou can use it for placeing on worktops or workplaces. Then you can see how...

Height extension for the snapmaker enclosure to fit the height extended snapmaker 1. ...Would be compatible with all parts of the enclosure frame.

Height extension for the snapmaker enclosure to fit the height extended snapmaker 1. ...Would be compatible with all parts of the enclosure frame.

see video here https://youtu.be/pK18BFSD1H8 Original Inventor files is here https://grabcad.com/library/snapmaker-enclosure-usb-extension-1 Printer model is here https://grabcad.com/library/snapmaker-3d-printer-cnc-laser-200mw-and-1600mw-1 Enclosure...

A modified version of the Snapmaker Enclosure Thread Guide by jnovack https://www.thingiverse.com/thing:2944871 Great for reducing tangles when feeding filament off the bottom of the enclosure spool holder. ...Modified to give it a little more strength...

I set up the Snapmaker enclosure for left handed opening and I am not using the touchscreen through the door panel. I created this handle to snap over the opening to eliminated drafts and make it easier to open the door. ...

The Snapmaker enclosure provides a fan, fitting, and hose to pull fumes and smoke from the enclosure. There was no fitting provided to attach the other end of the hose. Of course, there is no USA standard woodworking dust collector fitting that...

A protective cover for the opening of the Snapmaker A350 enclosure (should fit the A250 aswell) - since i have my unit on the floor under the desk, one might accidentially bump into the display i've just optimized the design by drspringer - with out...

I was having some trouble with the Snapmaker enclosure pulling a lot of PLA off the spindle. It looked sloppy and because of the twists it was causing issues. Now, you can see the PLA feed stays taut and neat. This thing was made with Tinkercad...

just a 2x2 brace I made for my snapmaker enclosure, you can use for any 2x2 lumber.

Made an adapter to connect my Snapmaker Enclosure exhaust host to a carbon filter. My enclosure is in the garage, but I don't have any windows that I can run the hose to. The filter is a 4" carbon filter: ...

The latter is useful if there is some distance between the vacuum and the Snapmaker enclosure. The exhaust duct connector has a 75mm (measured as 74.6 and rounded up) outside diameter. The picture shows the Direct adapter connecting to the vacuum...

Small cable-holder to fit in the enclosure rails of a Snapmaker 2 3d-printer. ...Used to hold cable for a camera that I attached to the 3d-printer

I designed these to use with my Snapmaker 2 A350 and Enclosure. I will be venting the enclosure using the supplied exhaust hose thru a partially opened window in my office. I will be mounting on 1/8" masonite or particle board to seal the window. ...

If you need better location for Snapmaker USB Memory Stick Then you can Print this New corner module.see video here https://youtu.be/pK18BFSD1H8Printer model is hereSnapmaker 3D Printer, CNC, Laser 200mW and 1600mWEnclosure model is hereSnapmaker...

This is a bracket that snaps onto any enclosure extrusion so you can screw on the aluminum bracket of the LCD screen. Depending on your printing resolution, if it is too tight of a fit you can sand it down. ...

Plate for sliding door to close & open the LCD on Snapmaker A350 Enclosure.

I started printing the original design and found out it fits the v1.1 snapmaker enclosures, which have larger center channels on the aluminum extrusions for larger corner tabs to slot into. So on my friend's v1.0 enclosure (original kickstarter...

Vent to replace HMI screen on Snapmaker enclosure. ...

This is a stand for a Tablet (1mm thick) like Firetablet 8. ...I attached it to the enclosure of my Snapmaker to use it for operating Octoprint.

This is a reducing shroud for a 92mm fan to allow it to fit on the snapmaker 2.0 enclosure. ...The shroud is asymmetrical to allow the fan to fit in the enclosure corner.

Since I moved the touchscreen from the front of the enclosure of my Snapmaker to the top, I was looking for somthing to cover up the hole when I'm milling but let air in when I'm printing. I used 4 M3 screws to keep everything together (in the...

Remix / inspired from ErikRudec (https://www.thingiverse.com/thing:3450378) Since I moved the touchscreen from the front of the enclosure of my Snapmaker to the top, I was looking for somthing to cover up the hole when I'm milling but let air in...

This is a very small remix of an incredible Snapmaker filament holder. ...I just closed the old holes and added 2 new ones to fit the mount for the Tapo C100 Security Camera.

This is a very small remix of an incredible Snapmaker filament holder. ...I just closed the old holes and added 2 new ones to fit the mount for the Tapo C100 Security Camera.</p> Category: 3D Printer Accessories

Moved the USB port closer to the front of the Enclosure using an USB extension cable and USB corner bracket. Single piece press fit and mounted on the bottom rail. ... Using 2ft USB Extension Cable:...

Moved the USB port closer to the front of the Enclosure using an USB extension cable and USB corner bracket. ...Single piece press fit and mounted on the bottom rail.</p><p>Using 2ft USB Extension Cable:...

Made some feet for the snapmaker V1 enclosure to put in the hoiles at the bottom of the enclosure. ... the mother screw needs some scaling in the slicer (I scaled the x and y axis by 4 percent - don´t scale the z !!) have fun

Rremove panel handle

Designed this to reduce the footprint of the Snapmaker 2 enclosure.