so 239 3d models
579228 3d models found related to so 239.pinshape
SO-239 usually come as a wall mount connector. ... I needed one for my rg-58.
thingiverse
This is a combination mount and holder I used for mounting an SO-239 based 1/4 wave antenna in my garage rafters. The hole is sized so that a PL-259 connector can pass through it. I am using it to both route cable and hold the antenna upright. ...The...
thingiverse
Four M3 screws, four M3 washers, and four M3 locknuts is the hardware I chose to use to attach the so-239 to the bottom mount. Used three different sizes of EMT conduit. 1/2, 3/4, and 1 inch. Used nominal sizes of the outer diameter of the pipes...
thingiverse
... are not mounted yet. Just put the thing on the back of a SO-239 chassis mount to make it more pretty and give you a mounting option. ...The little hole on the side is to fill the inside with a resin or something like that to make it watertight.
thingiverse
its probably already been done....but as a ham radio op I need to work with chassis mount SO-239 connectors....not having found a decent simple template to cut or add to my projects I modeled up the connector I have and have tested it and it fits...
thingiverse
SO-239 or N-type connector yagi boom mount sample of use look on video
myminifactory
This is a simple flexible cover for the SO-239 connetor made with TBU.
prusaprinters
This mount is intended to mount an SO-239 bulkhead connector into a 28mm-30mm panel hole. The SO-239 is used for Amateur Radio antennas. This is a remix of my M28 Panel Blank. Category: Hobby
thingiverse
... Print it slow and upside down with brim to get a nice result. The printed thread works nice however if it´s to tight you can slightly warm up the SO-239 socket with a heat gun (not to hot !) and screw the cap on back and forth to make it perfect.
grabcad
This is a threaded cap for a SO-239 antenna mount.You can install a O-ring to it if you want.Print it slow and upside down with brim to get a nice result.The printed thread works nice however if it´s to tight you can slightly warm up the SO-239...
thingiverse
This mount is intended to mount an SO-239 bulkhead connector into a 28mm-30mm panel hole. The SO-239 is used for Amateur Radio antennas. The nut is intended to keep the assemble from turning when mounter in a 19" 1U blank. It is not required,...
myminifactory
... Print it slow and upside down with brim to get a nice result. The printed thread works nice however if it´s to tight you can slightly warm up the SO-239 socket with a heat gun (not to hot !) and screw the cap on back and forth to make it perfect.
thingiverse
This is a mount to put the GoPro on a SO-239 magnetic car mount (antenna mount). You can safely shoot videos from the roof of the car. ...Use a heatgun to make the thread fit nicely in case it comes out a bit to tight.
grabcad
This is a mount to put the GoPro on a SO-239 magnetic car mount (antenna mount).You can safely shoot videos from the roof of the car.Use a heatgun to make the thread fit nicely in case it comes out a bit to tight.
myminifactory
This is a mount to put the GoPro on a SO-239 magnetic car mount (antenna mount). You can safely shoot videos from the roof of the car. ...Use a heatgun to make the thread fit nicely in case it comes out a bit to tight.
thingiverse
This will screw on to the end of a painters pole or broom handle, and support an SO-259 based quarter wave antenna
grabcad
Radio Shack Brand SO-239 Chassis mount UHF Connector. Normally used for Amateur Radio/CB RF Communications. Rated for HF/VHF. ...Would not use for UHF (even though its called a UHF connector)
thingiverse
A quick-to-print template to ease drilling, marking, or mock-up of where to place an SO-239 UHF chassis mount connector. Customizable as well (sizes if you'd like, but you can also remove the tab with the drill size reminders (which is largely...
cults3d
A quick-to-print template to ease drilling, marking, or mock-up of where to place an SO-239 UHF chassis mount connector. Customizable as well (sizes if you'd like, but you can also remove the tab with the drill size reminders (which is largely there...
thingiverse
This is a wall mount for two SO-239 Coax Lightning arrestors. The lightning arrestors I designed this around can be found here: https://www.amazon.com/gp/product/B08J81CJNF This might work with others, but it's not guaranteed! The only extra...
thingiverse
Ham Radio Operators may appreciate this: This is a very simple print which I designed because I needed to put a UHF/SO-239 barrel through the wall of my metal trailer. The trouble is that the trailer has a lot of electronics in it, some of which...
myminifactory
If the thread comes out a little bit to tight you can warm up the cap with a heat gun and screw it back and forth a few times then it will work nice.
grabcad
If the thread comes out a little bit to tight you can warm up the cap with a heat gun and screw it back and forth a few times then it will work nice.
thingiverse
Cap off unused antenna connectors to protect them from dust, water and contamination while in the field. Fit's just a bit loose, push it on and twist to feel the threads grab. ...
thingiverse
If the thread comes out a little bit to tight you can warm up the cap with a heat gun and screw it back and forth a few times then it will work nice.
thingiverse
Cover for outdoor use of S0-239 (UHF female) connectors. Designed for Elastan flexible filament, but might be suitable for other plastics. ...There are two variants of these - cap only with hole for tether and gasket for square mount socket with bound...
thingiverse
This is a template for punching holes in other objects for mounting an SO-239 panel mount connector. Import into your modeler and align it where you want the connector to go, passing through the objects wall. ... Set this to be a hole and you've got...
prusaprinters
... ...Import into your modeler and align it where you want the connector to go, passing through the objects wall. Set this to be a hole and you've got perfectly sized ans spaced holes for your so-239 connector quick and easy. Category: Electronics