squash feet 3d models
31526 3d models found related to squash feet.thingiverse
Low Profile Squash Feet for Anycubic I3 Mega Printer (and similar designs). ...Use squash balls to dampen vibration of printer from work-surface.
thingiverse
Now I've combined the damping of the original feet which is limited, with the damping of the squash feet which is huge. The printer is a lot more silent, and at least the first few prints are of a far better quality since the feet are installed. In...
thingiverse
Now I've combined the damping of the original feet which is limited, with the damping of the squash feet which is huge. The printer is a lot more silent, and at least the first few prints are of a far better quality since the feet are installed. In...
thingiverse
This is a mashup remix of Argasman's Dragon Claw with DrBoo's Squash feet base. I am still working on converting my CR-10S to a prusa style so I haven't tested them yet. ...
cults3d
This is a mashup remix of Argasman's Dragon Claw with DrBoo's Squash feet base. ...I am still working on converting my CR-10S to a prusa style so I haven't tested them yet.
thingiverse
Another squash ball feet I use this part to fix the feet on the printer : https://www.thingiverse.com/thing:3170442 Thanks, Enjoy! ...
thingiverse
Remix on “Squash Feet (longer)” by Popcorn To use new “Cover Plate for PSU” (https://www.thingiverse.com/thing:5990917) and “Cover Plate for Mainboard” (https://www.thingiverse.com/thing:5990907), you'll need these Feet to lift your 3d printer For...
thingiverse
The extra weight on the left is causing the printer to rest at an angle when using 4 identical squash ball feet. I therefore made some longer squash ball feet for the left side of the printer. So you can use these feet to replace the ones you made...
thingiverse
I developed these squash ball feet from other examples that we found in the thingiverse. I added the ability to adjust the height using a thread and nut. ...In case the surfaces where the printer is not properly leveled, they can adjust accordingly.
thingiverse
Remix of [Dr Boo's CR-10 Squash Feet](https://www.thingiverse.com/thing:2742599) to adapt it to a Kossel XL delta printer using 20mm extrusion profiles. The hole in the bottom of the ball slot is used to screw in the center hole of the vertical...
thingiverse
Fitted for 55mm diameter Raquet Balls, not Squash Balls! Can be printed upside down without supports. Print it using common sense, they're holding up your printer! So make'em beefy with lots of quality infill. ... Sized for M5 screws.
thingiverse
... some space for fans and components on my Hypercube Evolution. ... For the screws M5 are used and the squash balls are from [Amazon](https://www.amazon.de/Unsquahable-Squashb%C3%A4lle-Geschwindigkeit-Extra-Langsam-382213/dp/B004E8N2LS) (Double Yellow)
thingiverse
I wanted to try squash balls to see if I can reduce the vibration as well as improving my print quality because you can clearly see vibrations on my prints on the Y axis. Will squash balls actually help? ...Only time will tell, still waiting for my...
thingiverse
After various upgrades to my printer, I needed the feet to be a bit taller. ...So i created these and extended them to the sides so they would give it a bit more stability.
cults3d
After various upgrades to my printer, I needed the feet to be a bit taller. ...So i created these and extended them to the sides so they would give it a bit more stability.
prusaprinters
I needed this tall foot to get some space for fans and components on my Hypercube Evolution. For the screws M5 are used and the squash balls are from Amazon (Double Yellow) Print Settings Printer: Hypercube Evolution Rafts: No Supports: Yes...
thingiverse
I like the Squash feet by Artist11d found here https://www.thingiverse.com/thing:3050212 and also the PSU Fan cover by kuehmayer found here https://www.thingiverse.com/thing:3306465 When I fitted the cover to my PSU, it was very tight against the...
thingiverse
...Probiert es aus... ***ENGLISH*** I like the Chiron Squash feet of Serya, but firstly you need 2 left and right feet each and then I found the edge of the components a bit too flat. I also wanted a bit more stability in the sphere area. ...Try it ...
prusaprinters
a copy of an ANET printer using aluminium profiles and MGN linear rails. Print Settings Printer: TEVO TORNADO Rafts: No Supports: No Resolution: 0.2 Infill: 30-50% rectlinear Filament: Devil Design PETG black and green Notes: You may add a brim...
thingiverse
Even sitting right next to the printer, the sound produced is very low, pretty-much drowned out by my noisy fans (that's the next upgrade)." "Easy to installed and shocked at how much they cut down on the noise!" SQUASH FEET... Derived from...
cults3d
This is a remix of https://www.thingiverse.com/thing:2742599 I build a 3D printer with 2020 profiles at the moment so i adapted the design to fit my needs. ...No need for supports, the screws are M5. Use "yellow dot" squash balls.
thingiverse
This is a remix of https://www.thingiverse.com/thing:2742599 I build a 3D printer with 2020 profiles at the moment so i adapted the design to fit my needs. ... No need for supports, the screws are M5. Use "yellow dot" squash balls.
thingiverse
Minimalist Squash Ball feet dedicated for 3030 Item Profile. ... Enjoy!
thingiverse
https://www.printables.com/it/model/191530-generic-squash-ball-feet I quickly modified a couple of popular models of squash ball feet because i found out that if you move the printer without lifting it enough, the grip it makes onto the surface might...
thingiverse
Prusa squash ball feet supports Prusa i3 MK3s Layer height: 0.15, wall line count 4, top & bottom layers 6, Infill: 30-40% Pattern: Octet, Support: No, Material: PLA Hardware: use 2 m3 x 16mm long screws & 2 m3 t-nuts for mounting each foot & 4...
thingiverse
It uses a square base for aesthetics and some squash feet like these;...
thingiverse
squash ball feet for 2040 aluminum extrusion style frames v1 and v2 are for straight up 2040 aluminum extrusions v3 pushes the foot closer to the corners of the machine for more stability it mounts on the 2040 side extrusions and on the 2020 front...
prusaprinters
There are no more noise from the wall/bookshelf, and i can only slightly feel vibrations when placing my hand on the shelf plate.The squash ball is clamped to hold it in place, this will probably deform the ball over time.There is a small cutout for...