strix goblin 3d models
5159 3d models found related to strix goblin.thingiverse
Strix Goblin Top Canopy replacement comes in three flavours: - Clean top canopy - With extra air intake - With air intake and support for FPV camera, and holes for cable pass-through the anchor file is printed and glued with cyano
thingiverse
This is a 3D printed TPU nose protector for the Strix Goblin flying wing. I use a runcam2 in the nose of my Goblin, but after a nasty crash, the nose was quite damaged, so I made a protection for it. ... Use 4 2mm bolts, I used some I had laying...
thingiverse
This is another Flight Computer mounting plate for the Strix Goblin. The intention was to place the computer in a serviceable position with enough room underneath for a battery. ...There are miscellaneous cable management cutouts and holes to lend...
thingiverse
here some parts for make a clean install inside Strix Goblin. ... more info here : https://www.rcgroups.com/forums/showpost.php?p=39639282&postcount=2404 For Pitot print, rotate around Y axis, -90 degrees (front of part look vertical to the top) ...
thingiverse
Replacement Tab for Strix Goblin, Can be inserted in the wing without opening the wing
thingiverse
This is a replacement front latch for the Strix Goblin. There are two stl files the file NoseLatch.STL has no mounting tab on the back and is meant to be used if you can get a decent quality print of NoseLatch_Tab.STL. NoseLatch_Tab.STL is meant to...
thingiverse
Caddx Vista mount for the Strix Goblin. This mounts the camera in the nose of the fuselage, and has a holder for the antenna. Features: - Two mounting methods: right side up or upside down. This allows you to choose whether the antenna sits...
thingiverse
TPU fixations to hold in place the inner wooden structure of the Goblin. ... After a few hard landings, the wooden inner structure tended to unglue and move around, so I made these to hold it in place.
thingiverse
I had a bad crash with my Strix Goblin and broke the rotating lock which hold the lid on, so i designed a replacement
thingiverse
This is a frame to mount a DJI Air Unit plus Camera into a Strix Goblin. Print in PETG or ABS, because the Air Unit might get too hot for PLA. Front holes fit exctly between the Air Intakes. They will be blocked, air will enter trough the Gap...
thingiverse
Easily mount your RunCam HD2 in the nose of your STRIX Goblin with the help of this simple platform. Attach by using two screws through each air inlet. ...The height of the platform should be right to allow the camera to attach to the plate via velcro...
cults3d
Remixed the Strix Goblin HD mount to mount a Swift or Split into the nose of the Goblin. Tried it with the split first and while it works the split is a pain to get in and out so replaced it with a swift. ... Split V2 - Moves camera ahead 3mm and...
thingiverse
Remixed the Strix Goblin HD mount to mount a Swift or Split into the nose of the Goblin. Tried it with the split first and while it works the split is a pain to get in and out so replaced it with a swift. ... Split V2 - Moves camera ahead 3mm and...
thingiverse
This is a design for my Strix Goblin easy fc install tray. I have included a 'basic' version with the minimum required parts to make this work - so that you can make your own variation. The version with all the parts is specifically setup for...
thingiverse
Swift mount for strix goblin nose. Mount is printed upside down. Tray then mounts on top to aid in GPS mounting. From left mounting point to right mounting point is 63mm. Units were incorrect on export, so be sure to resize (reduce the size...
thingiverse
Some people have found that the replacement CNC machined aluminium motor mount for the Strix Goblin is a little loose. When fitted there is a small gap between the motor mount and the fuselage, which causes the motor to pivot. This small spacer...
thingiverse
I printed the original thing for a friend to put in their Strix Goblin. The issue they had was mounting the RunCam Split V2 board in a way to gain access to the USB port or Micro SD card slot meant accessing the buttons was a bit of a pain. I decided...
thingiverse
So.. ...this is my heavy duty mount to hold the Cadx Turtle in the nose of the goblin. ...
thingiverse
Designed for the DJI/Caddx Vista with Nebula Pro camera to mounted in the nose of the ReadyMadeRC Strip Goblin. M2 20mm x2 & 2 nuts to attach vista M2 12mm x2 & 2 nuts to attach the mount to the goblin. Place the mount in goblin without screws. ...Use...
thingiverse
Lot of ppl experience problems with not properly locking canopy of the big Goblin. So I designed the thing new, trying to overtake the original system. There are 3 different knobs to bolt on to the canopy side. Additionally to the original one,...
thingiverse
i got tired of braking the balsa wood battery tray on small or soft crashes so i designed my own. that's much stronger. ...with larger battery strap holes i also pushed out to the sides to fit bigger batteries easier and make it much easier to replace...
thingiverse
Made a new stronger support, thicker walls and rounded angles used PLA
thingiverse
Strix Nano Goblin servo covers. Pictured covers has a custom graphic added. ...Files posted are blank.