subaru oil filter wrench 3d models
53466 3d models found related to subaru oil filter wrench.prusaprinters
Made this so I could more easily remove the oil filter on my Outback during oil changes.This fits subaru filter # 15208AA15AI printed in PETG (cuz it stays in my hot AF garage in TX) with the following settings:2.5mm LH , Arachne auto-width , 5...
thingiverse
Customized version of https://www.thingiverse.com/thing:1417160 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=1417160 This should fit all EJ engined Subarus. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:1417160 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1417160
thingiverse
This is an oil filter wrench for gen 5 Subaru Outbacks. It fits the Subaru 15208AA15A oil filter. ...I sized it a little larger to clear.
thingiverse
This is a no mess oil filter wrench funnel to be using during normal maintenance oil changes on the Subaru EJ series motor. This is designed to fit authentic Subaru oil filters (specifically part number: 15208AA12A). I was tired of getting covered...
thingiverse
Oil Filter Wrench - With F3D (Worked with Subaru 2019) Printed with PLA with lots of walls. Since the work is done when everything is cool, PLA works fine. If this designs helps you in any way, do you mind leaving me a quick tip via paypal? ... ...
thingiverse
Customized version of https://www.thingiverse.com/thing:2752150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2752150
thingiverse
Customized version of https://www.thingiverse.com/thing:2752150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2752150
thingiverse
Customized version of https://www.thingiverse.com/thing:3610339 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3610339
thingiverse
The wrench fit to a oil filter cap (27mm hex) with hard access like Ford Galaxy 2.0 TDCI. ...
thingiverse
Oil filter wrench Clef de filtre a huile. ...14 Faces, diameter 64mm Print Settings Rafts: No Supports: No ...
grabcad
76 mm 12 flutes renault oil filter 3d printable wrench, 32 mm hexagon nut or 1/2 inch square socket for applying torque.
thingiverse
I forgot my regular oil filter wrench the last time I was doing an oil change at the mooring. What a pain! I had to use a screwdriver and a hammer to drive it through the housing in order to loosen it. This tool allows you to loosen your oil filter...
cults3d
FRS, GT86 and BRZ Oil Filter Wrench based on stock wheel design. Fit 1/2 or 12.5mm breaker bar. ... I designed it to be perfectly fit so make sure you calibrate your printer before you print.
thingiverse
This is an oil filter wrench for my 2017 Fiesta. There were a lot of that size filter on the shelf at Walmart, so I assume it goes on lots of cars. So this my be of use to someone. 7-13-19 Version 2, I increased the size of the wings. ...I stripped...
cults3d
This is an oil filter wrench for my 2017 Fiesta. There were a lot of that size filter on the shelf at Walmart, so I assume it goes on lots of cars. So this my be of use to someone. 7-13-19 Version 2, I increased the size of the wings. ...I stripped...
thingiverse
It ended up not working for me because my oil filter was /extremely/ tight and the thin metal of the filter stripped (not the fault of the wrench), and I had to use a Lisle 63600 wrench (which I highly recommend for these situations), but if your...
thingiverse
... Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1417160 Fits the following Oil Filter: Champion "COF203" 14 faces, wrench: 0.375 inch or 9.52 mm, round on outside, diameter between opposing faces: 64mm or 2.519 inch
thingiverse
Made for the Subaru Legacy/Forester/Impreza/WRX standard oil filter (66.5mm, 14 flats). K&N PS-1008 pictured. Features a funnel at the top, drip channels and a reservoir in the bottom to catch and hold the oil that drips when the filter is...
thingiverse
A customizable parametric oil filter wrench. Create 3/8" drive or 1/2" drive filter wrenches of any size you need. It's not pretty, but it's designed to be easy to print and strong. (Print it with high infill percent for strength.) 2017 03 29: ...
grabcad
Oil filter ratchet for 3d printing (no supports), fits for Alfa Romeo Gullietta, Mito on other fiat cars with 1.6 JTD engine with 32 nut size oil cap. Tested - with one oil change worked with no issue. I printed of PLA but should work better with ABS...