tablet stand for bike trainer 3d models
2357009 3d models found related to tablet stand for bike trainer.thingiverse
... It could also be used for Zwift or whatever you want to watch... maybe just netflix, whatever you prefer. Willing to adjust it for an iPad or some other tablet if you need something specific or need a bigger diameter on the handlebar clamp.
prusaprinters
This is a universal tablet shelf for a stationary bike. I used an old MTB with a Tacx Flux S roller trainer and use Zwift and Tacx Apps on my phone to do the workouts. Therefore I needed a shelf to put on the phone/tablet. I printed the shelf in...
thingiverse
Cyclists in cooler climates will often ride on stationary bike trainers in the winter to keep up their conditioning. This can get kind of boring. A tablet could provide much needed entertainment if only there was a way to mount it. This thing was...
thingiverse
This is a universal tablet shelf for a stationary bike. I used an old MTB with a Tacx Flux S roller trainer and use Zwift and Tacx Apps on my phone to do the workouts. Therefore I needed a shelf to put on the phone/tablet. I printed the shelf in...
thingiverse
Positioned diagonally this just fits, then the stand is held in place by the end caps on the cross trainer arms and the pressure from the foam covering. There are also round rings that could be attached to avoid the end caps sitting at an angle that...
thingiverse
A holder for a tablet or a phone, so you can watch something while you are exercising on a home trainer bike and not block all controls and the speed. It fits on a H22 from viva. ... Simply print and slip on the screen.
thingiverse
so I have been cycling indoors with a bike trainer. It gets kind-of boring so I have been looking at options to pass the time while cycling. I 3D printed this tablet holder so that I can read while cycling ... it works really well. My inspiration...
thingiverse
My wife recently purchased a bike trainer for her road bike. Not wanting to purchase the special front wheel stand I made this up really quickly in OpenSCAD. Print out two, attach to some wood with the right spacing for your bike and off you go!
prusaprinters
The slot is curved to match the profile of the wheel for stability, so 26"ers won't fit well. Slot is 28mm wide but scale the print if your tire needs more room. ...It can print on a 220mm bed if rotated as in photo.</p><p>The block is embossed with the...
cults3d
Optionally, add bar tape or rubber tape to the tablet holder portion to increase grip. If you're worried about sweat, use the longer version, if not, use the short version that should be quick to print. ... I printed mine without top and bottom...
thingiverse
A holder made for a small tablet. ...Further (4x) M3x25 Screws and Screw-nuts are necessary.
thingiverse
This is a tablet holder for a bike trainer. I tried to design it without the need for screws. You simply place it around handlebars stem and fix it together. ...**dist** plugs can be used to set the tablet angle and **pin**s can hold it in a position.
thingiverse
My indoor bike trainer had a plastic component holding a steel plate in place to create resistance with the rotating magnets. The plastic part cracked and it didn't function any longer. I modeled this replacement part and 3D printed it to get the...
thingiverse
This is a front wheel riser for use with a bike trainer. One slot will accommodate up to a 25 mm road tire, and the other slot will accommodate up to a 2.2 in mountain bike tire. It raises the wheel about 70 mm or 2.75 inches (because that's the...
cults3d
Original rise the front Tire to 2,5cm or 5,0cm with the additional Bottom Stand it rise up to 7,5cm and 10cm Original from TroyDL: https://www.thingiverse.com/thing:903537 Bicycle Front Tire Riser for bicycle trainer stands by TroyDL, published Jun...
thingiverse
Original rise the front Tire to 2,5cm or 5,0cm with the additional Bottom Stand it rise up to 7,5cm and 10cm Original from TroyDL: https://www.thingiverse.com/thing:903537 Bicycle Front Tire Riser for bicycle trainer stands by TroyDL, published Jun...
prusaprinters
Original rise the front Tire to 2,5cm or 5,0cm with the additional Bottom Stand it rise up to 7,5cm and 10cm Original from TroyDL: https://www.thingiverse.com/thing:903537 Bicycle Front Tire Riser for bicycle trainer stands by TroyDL, published Jun...
thingiverse
I had merged two things for my use. ... Adjustable tablet holder for DJI Mavic PRO by smsagent https://www.thingiverse.com/thing:2020007 Tablet holder for cross trainer by MS_Engineering https://www.thingiverse.com/thing:2233506
thingiverse
** Adapter for a Tacx Cycleforce Basic Bike Trainer ** ----------------------------------------------------------------------- My bike did not fit on the bike trainer, because of the handle on the wheel. When you buy one of these bike trainers you...
thingiverse
You can adjust dimensions in the .scad file: /* dimensions for bike */ include_nut=0;//set to 1 to include relief for a nut, 0 for no nut bolt_d=3/8*25.4; //sized for 3/8-inch dia nut_t=1/4*25.4;//thickness of nut (sized for 3/8)...
thingiverse
My son wanted to ride his pedal bike but it was snowing outside, so I made up these cups that allow him to pedal indoors. ...You may need to adjust the design to fit your child's wheel size.
prusaprinters
This model can simulate 3%/5%/7% incline for my bike. 7% is perfect for a Road to Sky ride. ...My tyre is 700C x 25mm, but it should be okay for 30mm. Material: PLAInfill: 15%Perimeter: 4
thingiverse
Tablet holder for training bike. Update (16/02/19): Fix Bot et Screw piece. ... Update (17/02/19): New design for the bolt.
cults3d
Tablet Stand - tablet holder 3D printing settings: Filename: tablet stand.STL Size mm: 99 x 173 x 100 Volume mm3: 181,423 Triangles: 18,880 Time: 7h05 website http://filestl.com
thingiverse
Phone or tablet stand that fits Peloton bike handlebars.