tgy i6 3d models
704 3d models found related to tgy i6.thingiverse
TGY-i6s screen holder for some screen (Eachine I think) that I have for a while now. It might work for other screens, I haven't tried. I printed the one in the pictures sideways because I had cooling issues if printed vertically. It prints well...
thingiverse
This is a screen holder designed for use with the Turnigy TGY-i6 and attached to it's handle. The screen I used for this was a "Car 4.3" TFT LCD Color Rearview Monitor for DVD GPS" off of eBay. Note- The Screen Holder .STL appears to be flat. It is...
thingiverse
I managed to lose a set of side buttons whilst performing some modifications inside my FS-i6. These work as replacements. Nothing fancy or complex. One half is slightly taller , so if they are too loose or tight on the push button - flip them over.
thingiverse
Battery support to Flysky Fs-i6 and Turnigy TGY-i6 whit module IrangeX (multiprotocol)
thingiverse
A protective case for the TGY-I6S radio controller. I designed it with simplicity in mind. After multiple reiterations, I think the design works quite well, and doesn't require a lot of filament to print. Prints nicely, you have to use supports but...
thingiverse
I make this for my Samsung Galaxy Note 4 but it can stretch from 10cm to 15cm depending on the spring you will use and the thickness of the mobile can be up to 9mm
thingiverse
This is design to protect your sticks during transportation of your transmitter. ... I have an issue on printing the "FS-I6S" label on my printer, should be solved on a futur version.
thingiverse
Because I didn't find a gimbal protection for the FS-i6S i designed one by myself. Therefore I used the screw of the mobile/tablet mount that came with the radio but a normal M6 screw is also possible. Works pretty well. It holds the sticks in the...
prusaprinters
Because I didn't find a gimbal protection for the FS-i6S i designed one by myself. Therefore I used the screw of the mobile/tablet mount that came with the radio but a normal M6 screw is also possible. Works pretty well. ...It holds the sticks in the...
thingiverse
A mount for Huawei P9 Lite on I6S radio transmitter. NOTE: It's designed to fit the P9 Lite WITH a silicone case. ...I prefer it that way, as I don't have to remove the case first, and secondly it holds it better :)
pinshape
Summary A mount for Huawei P9 Lite on I6S radio transmitter. NOTE: It's designed to fit the P9 Lite WITH a silicone case. ...I prefer it that way, as I don't have to remove the case first, and secondly it holds it better :)
thingiverse
Supporto per trasmittente che si adatta perfettamente al case, si aggangia tramite foro e fileto già esistenti senza modificare il radiocomando. ... Si stampa molto facilmente necessario usare qualche supporto.
thingiverse
Simple gimbal/stick protectors Print Settings Printer: GEEETech I3 PRO B Rafts: No ...
thingiverse
Gimbal cover / protector to prevent sticks getting mashed about when being carried in a bag etc. Print in ABS or PLA, infill at least 25%. ...Supports to bed on.
thingiverse
Hallo i made a simple but very robust Monitor Holder for the TGY i6 Flysky. ...You need two 3mm srews 20mm long and a camera screw for the monitor
thingiverse
Neck strap balancer for flysky fs-i6 or Turnigy tgy-i6 Is a remix from http://www.thingiverse.com/thing:1748966
thingiverse
Neck strap balancer for flysky fs-i6 / Turnigy tgy-i6 Print Settings Printer: Wanhao Duplicator I3 Rafts: No Supports: No Resolution: 0.15 Infill: 100% Notes: Mount it with M4 bolt and nut.
thingiverse
I made up my own little PCB containing a Turnigy TGY-IA6B receiver (came with the TGY-I6s TX i bought for my daughter) and connected this to the PPM pin of the Taranis module bay and configured it to use SBUS (i prefer this over CPPM). Since this...
thingiverse
... held on with an elastic strap around the case. You could also use velcro strap (up to 20mm wide). As with the original design, you can bend the switch protectors down with a heat gun. This will also fit the Flysky FS-i6X and the Turnigy TGY-i6.
thingiverse
Customized version of http://www.thingiverse.com/thing:813330 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1731842 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1731842