tube amp chassis 3d models

Tube amp chassis

an old but very nice vacume tube amplifier

...... Also requires M3 screws and M3 nuts to attach the amp to the chassis and the sides to each other. Print two long sides, two short sides and five back pieces. The piece with terminal cutout would have to be trimmed down/might not fit work at all.

A customized Tube chassis for an off-road buggy.

Mini TUBE Pre-Amp if you like or download my model, hit the ‘♥’ button before you go That is the only payment. ...Enjoy :-)

This is a bracket for switches one or two way. ... The build is intended for rapid prototyping of DIY tube amplifiers. Made with PLA and 30% infill. ... More DIY 3D printed parts and DIY circuits in my site: http://agalavotti.altervista.org/

This is a tiny, all tube guitar amp. The design exists all over the web, but repackaged by me to fit into a Hammond 1590B housing. Output transformer is a Hammond 125A (3 watt, Fender Reverb replacement). The power to the tubes is provided by a...

3mm diameter solid tube chassis. ...All one piece.

Started to make a tube chassis for a Challenger 71. ...still a work in progress

A simple agricultural robotics tube chassis joint can be created between two sections of 1-5/8" chain link fence post by bolting together four 1.5" automotive exhaust clamps with two 1/8" steel bars drilled for 5/16" u-bolts.

Made out of 0.5in tube for easier viewing, can be changed for whatever you like in weldments

I have measured a destroyed EL 84 RFT tube and implemented it in Rhino for mac. ...It is an old tube from RFT (east Germany, GDR).

Hybrid Tube Amp for the Raspberry Piif you like or download my model, hit the ‘♥’ button before you go That is the only payment. ...Enjoy :-)https://www.kickstarter.com/projects/1815752970/hybrid-tube-amp-for-the-raspberry-pi?ref=nav_search

This is a rendering of my real existing EL84 SE tube amp. I built this last year. It used two EL84 tubes and two ECC85 (or ECC83) tubes. Also one EM83 magic eye. It is an SRPP PCB layout. ...The rendering and design are made with Rhino CAD for mac.

This is a knob for my 503HTA Hybrid tube amp, from Pi2 design; http://www.pi2design.com/store/p13/503HTA_-_Hybrid_Tube_Amp.html As wide a knob as reasonably fits on the amp without blocking the adjacent attenuation switch. A full 20mm of depth...

This is a snap fit case for a cheap [DIY tube amplifier soldering kit](https://www.aliexpress.com/item/Fever-6J1-tube-preamp-amplifier-board-Pre-amp-tube-amp-6J1-valve-preamp-bile-buffer-diy/32590874810.html?spm=a2g0s.9042311.0.0.6dab4c4dIxM1JQ) that...

This is a snap fit case for a cheap DIY tube amplifier soldering kit that comes as a bare PCB. I got the amp to go between a Bose 2.1 speaker and even older record player. The amp is fun to look at and the sound is ... ok. It also needs a ground loop...

Tube used for Wheel Housing

4 link brackets kit .062 styrene rod chassis but can be adpated using 3d builder

amp

Amp

AMP.

just learnin....

This is a logo for Academy of Marketing Production. ...AMP is a class at Cyprus High.

A guitar amp meant to be edited into a picture. ...Its normal map might be a little too aggressive.

Guitar amp just practicing modeling Besure to check out my portfolio www.bobrokgames.com follow me on facebook www.facebook.com/bobrokgames

This is my first attempt at designing a tube chassis for a hobbyiest race car

This hood slips over the amp and uses 1mm stainless mesh to block any RF interference as a faraday cage. Also has cable guides to cleanly route them to the back of the amp. Conveniently stacks on top of the Nobsound solid state amp. ... Print...

I have measured a destroyed ECC85 RFT tube and implemented it in Rhino for mac. ...It is an old tube from RFT (east Germany, GDR).

I have measured a destroyed ECC83 RFT tube and implemented it in Rhino for mac. ...It is an old tube from RFT (east Germany, GDR).