unifi ap lr mounting bracket 3d models

Remixed to work with the UniFi AP-AC-LR mounting bracket

ctpearson's 2nd revision of their mounting bracket had tabs that were too large to fit my AP Lite so I took their original design and remixed it so the center was cut out for better heat dissipation. ...The fit isn't perfect but its good enough for my...

Ubiquiti UniFi AC Pro AP Mounting Bracket It works, might be a little too tight for your taste, you could shave a fraction of a mm off the bottom to loosen the fit. I omitted the snap in place lock arm the original has. I wanted to mount my...

As I didn't want to mount the access point (UniFi AP-AC-LR) to the wall or ceiling, I have created a stand for it. 4 x M4 screws are required to mount the stand to the access point. No nuts are required.

As I didn't want to mount the access point (UniFi AP-AC-LR) to the wall or ceiling, I have created a stand for it. 4 x M4 screws are required to mount the stand to the access point. ... No nuts are required.

This is a replacement ceiling mounting plate for the Ubiquiti UniFi AP-AC Lite and the Ubiquiti UniFi AP-AC LR. (Tested on the Lite model only, but the LR supposedly uses the same mounting plate.) Unfortunately a mounting plate was lost during some...

Mounting bracket for Ubiquiti Unifi APs. It should fit UAP-AC-LR, UAP-AC-LITE, and UAP-NANOHD. The mount included with these APs requires punching holes through the ceiling tiles. This bracket can leave the ceiling tiles without noticeable damage...

Mounting bracket for Ubiquiti Unifi APs. It should fit UAP-AC-LR, UAP-AC-LITE, and UAP-NANOHD. The mount included with these APs requires punching holes through the ceiling tiles. This bracket can leave the ceiling tiles without noticeable damage...

##Mounting bracket for Ubiquiti Unifi APs. It should fit UAP-AC-LR, UAP-AC-LITE, and UAP-NANOHD. The mount included with these APs requires punching holes through the ceiling tiles. This bracket can leave the ceiling tiles without noticeable damage...

English: I've created this design to put my Unifi AP LR and Enterprise to my ceiling. I have network cable coming out of the concrete and I didn't wanted to play with mini cable. So with this design, I can have a cable of 20 - 30 cm and roll it in...

This is a new Ubiquiti UniFi AC AP Lite/LR ceiling or wall mount extension. It was created to fit with standard US plastic ceiling mount electrical boxes, using 3-1/2" screw spacing. From the AC AP side, you can use the small drywall screws...

A replacement mount for AP-Pro WLAN Access points. The cable management hole is off center due to an inaccurate template the mount was based upon. This does not prevent usage so I did not end up correcting it. Take this into account when mounting if...

A modular L-shaped wall bracket for the Ubiquity Unifi AP. ...The bracket should be attached with M3 screws to the AP holder ( same as this one: https://www.thingiverse.com/thing:2883704 )

This is a construction bracket that mounts a Unifi Nano HD AP. I made this to install in a new home I'm building similar to a regular outlet box. It nails or screws to a truss or wall stud. When drywall is installed the drywall is cut out around the...

UniFi AP AC Lite Bracket Replacement (improved) Compatible with Ubiquiti Networks Wireless Access Point, 2.4GHz/5GHz, 867Mbit, 122m 1x 10/100/1000, 24V Passiv PoE, UAP-AC-LITE (1x 10/100/1000, 24V Passiv PoE 160 x 31.45 mm Indoor)

I just needed a slightly extruded surface so the mount stick off the wall about 3mm more.

Bought an AP-LR which didn't come with a bracket, so here is one.

This is for Unifi AP

Bought an AP-LR which didn't come with a bracket, so here is one. Category: Computer

Mounting bracket for the Ubiquiti Unifi Dream Machine (UDM). ...

A friend is building a new house and had electric junction boxes mounted where he plans to install Unifi APs on the walls. Those APs require a mount adapter that connects the AP backplate to a standard US wall box. These adapters hug the wall closely...

Mounting bracket for the Ubiquiti Unifi Dream Machine (UDM). Print instructionsCategory: Computer Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Filament: 3DJake PETG Black Notes: 3...

A remix of standard unifi gen 2 AP brackets to be able to be mounted to a pole with cable ties or screwed to a wall. ...No locking tab so idea for temporary installations.

Updated version with a stronger mount and support for U6-Lite on top of U6-Pro.DesignThis wall mount is designed for a variable wall slope. Actually it can be used for any angle from 90 to 0 degree. It fits the Ubiquiti U6-Pro and probably many other...

Replacement for the Mounting Bracket of Ubiquiti's UniFy Access Point, AC Lite.

DescriptionThis took me quite some time to model.With this print consisting of 3 parts, that slide together easily, you can mount your Unify Accesspoint on a drywall without visible cables. It uses the same hole pattern as the one provided by...

This is a remix of hot_soup_in_space's model. ...I have just extended the space between the ceiling and mount.

In addition to the printed parts you also need: • 1x M6 screw (to attach the mount to the ceiling) • 3-4x M3 screws with nuts (to attach the mount to the AP mounting plate) • 4x M4 screws (to fix the tube) • 1x tube (preferably aluminum) with the...

In addition to the printed parts you also need: - 1x M6 screw (to attach the mount to the ceiling) - 3-4x M3 screws with nuts (to attach the mount to the AP mounting plate) - 4x M4 screws (to fix the tube) - 1x tube (preferably aluminum) with the...