unifi g3 instant 3d models
8126 3d models found related to unifi g3 instant.prusaprinters
I was looking for a stable desk mount for my Unifi G3 instant cameras that could be elevated more than the existing models I found. After printing the nanoHD DeskStand from BradleyB, I was impressed with the stability and desided to remix it for...
prusaprinters
If you want other screws, modify the attached AutoCAD file. BOM:2x SPAX Screw 4mm for wall mounting2x SPAX Screw 3,5mm for camera base mounting Default base mount also as print here:...
prusaprinters
Simple ceiling mount for Unifi G3 Instant camera with a 45-degree angle. Currently, V1 is using double-sided nano tape to attach it to the ceiling, which seems to be just fine. ...Maybe over time, might add some screw holes later on.Used Slackers...
thingiverse
... screws, modify the attached Fusion360 file. BOM: 2x SPAX Screw 4mm for wall mounting 2x SPAX Screw 3,5mm for camera base mounting Default base mount also as print here: https://www.prusaprinters.org/de/prints/56466-unifi-protect-g3-instant-mount
prusaprinters
Mount for a UniFi G3 Instant camera to a baby crib. You can route the USB cable through the holes in the model to hide the cable neatly.</p><p>I recommend printing both models upside down, with supports on. I'm fairly certain that the clamps that...
thingiverse
Here for your taking is my window mount for a Ubiquiti UniFI G3 Instant camera. I have mine pointed out my back window and glare from inside lights caused reflections of inside to appear on the camera regularly. This camera shroud/cover helps cut...
thingiverse
Outdoor Housing for a "Ubiquiti Unifi G3 Instant" Camera. ... I created this by remixing three designs: "Stable and waterproof OpenSCAD case" by pbtec "Customizable Ball Joint" by kijja "90° Bracket (Parametarised)" by gineer Thanks to the...
prusaprinters
(If not Adjust the "ball nut tolerance"parameter in the case openSCAD file and create a new STL file.)Step 4: Wire-up and fit the cameraThe Unifi G3 Instant Camera is normally powered by a 5Volt adapter with a right-angledmale USB-C 2M long...
thingiverse
First Version of Cam Holder for USB power supply. ... First version, might not work ...
thingiverse
Replacement base for Unifi G3 Protect Instant camera or can be used to make a custom mount.
thingiverse
My son created this as I have a number of G3 instants that are required to sit on a windowsill / shelf. This is 12 cm ((4.75 inches) high so that the camera can sit within the overall height if required. The top is rounded to run with the Unifi...
thingiverse
This is a Unifi G3 Instant camera mount for the Ultimakler 3 printer. ...It mounts via the screws already in place on the printers side panel.
thingiverse
Mounting base model for Unifi Protect G3 Instant camera. ...Can be added to your custom mount to give you a single piece solution to meet your needs.
prusaprinters
UniFi's G3 Instant is a great little camera, but it tends to fall over, especially if there are children nearby. This model creates a basic stand for the camera, making it harder to tip over. ...Includes a rear opening for the power cable. </p>
prusaprinters
Can be added to your custom mount to give you a single piece solution to meet your needs. Print instructionsCategory: Camera Summary Mounting base model for Unifi Protect G3 Instant camera. ...Can be added to your custom mount to give you a single piece...
thingiverse
1-Gang plate with 22.5 degree vertical tilt to mount a UNIFI G3 Instant camera. All screw and nut holes are designed for #6-32. ...Recommend using #6-32 screws with #6-32 nuts for the G3 Instant mounting bracket and 3/4" - 1" screws for the plate mount...
prusaprinters
<p>Should work with any tripod with ¼-20 threads. ...Note that when slicing I used the color change feature to allow for inserting a ¼-20 nut.</p><p>All materials used: </p><ul><li>2x heatset inserts (Voron spec) </li><li>2x M3x6...
thingiverse
Unifi G3 Protect Instant camera 45 degree corner base.
thingiverse
Unifi G3 Protect Instant camera 45 degree base. Using my camera for a baby cam but it did not have enough down angle. ... Can use original screws since the screw holes are recessed.
prusaprinters
I've added them so that you don't have to bother with adding additional supports. For the side/little tabs that connects to camera I've referenced the design by Slacker - from here...
thingiverse
A simple cylindrical wedge to add 22.5° to the UniFi Protect G3 Instant camera mount. Use the original screws and mounting plate. Note that the screws will also be at an angle relative to the mounting surface and shortened by the width of the...
thingiverse
This is similar to other 22.5 degree G3 camera brackets I found on here. ... I wanted one with a slot to use a velcro strap or a zip tie to attach the bracket to a mounting surface.
thingiverse
A cover for the G3 Instant for Unifi Protect, to make it a bit more outdoor-durable. No guarantee though, as my own cameras have only been outside for a few days now (including heavy rain, but again, no guarantee). I recommend putting a bit of...
prusaprinters
Friction fit stand/holder for Unifi Protect G3 Instant. Cutouts for both microphone and USB-C cables. ...This model is tilted backward by 15 degrees and was designed as a wall mount to use the G3 Instant for a crib camera.
prusaprinters
Friction fit stand/holder for Unifi Protect G3 Instant. Cutouts for both microphone and USB-C cables. ...This model is tilted forward by 15 degrees and was designed as a table or above-cabinet mount to use the G3 Instant in an elevated...
prusaprinters
Friction fit stand/holder for Unifi Protect G3 Instant. Cutouts for both microphone and USB-C cables. ...This model is tilted forward by 25 degrees and was designed as a table or above-cabinet mount to use the G3 Instant in an elevated...
thingiverse
One of my Unifi Protect G3 Instant camera is standing on a high cabine but needed a bit of a down angle (25 degrees) to get a better picture of the whole room. Unfortunately, the default camera can only stand straight up, or needs to be wall...
prusaprinters
One of my Unifi Protect G3 Instant camera is standing on a high cabine but needed a bit of a down angle (25 degrees) to get a better picture of the whole room.Unfortunately, the default camera can only stand straight up, or needs to be wall mounted...
thingiverse
Summary Unifi G3 Protect Instant camera 45 degree base with mounts shifted by 90 degrees to the left. Using my camera for a baby cam but it did not have enough down angle. Can use original screws since the screw holes are recessed. Print...