vector rails 3d models
46566 3d models found related to vector rails.thingiverse
These are Vector Rails I made connectors so you can connect more than one rail together if you have a small printer. Or, your printer isn't big enough for the hp you are wanting to print. The support part is for the Full Rail. If you are printing...
thingiverse
Krytac Vector Rail, combination of (Superpoo and GohDesign) designs and measurements. Not yet tested. ...For Airsoft Use.
thingiverse
A simple frame to hold a pair of vector rails (TS100 series) at the proper spacing for eurorack panels. This is a quick design I made in order to begin prototyping a rack system while I build a more permanent case. ...It turned out well enough I may...
prusaprinters
A simple frame to hold a pair of vector rails (TS100 series) at the proper spacing for eurorack panels. This is a quick design I made in order to begin prototyping a rack system while I build a more permanent case. It turned out well enough I may...
cults3d
Krytac Kriss Vector rail system pack of 3 - R3D limited edition, limited edition but with mlok, and smaller mlok with top rail.
cults3d
This Model Is Only Suitable for KWA Kriss Vector, It Adds Spike As a Guard or Rail to Make Your Kriss Look More Wickedly Futuristic. I Have Not Tested On Krytac Kriss Vector, But It Might Work With Little Modification. You Need Several Flat Head M4...
thingiverse
Rail Riser to suit Lehui Kriss Vector Gel Blaster Designed to replace the picatinny, print either the normal one and the picatinny or you can try the re-use picatinny, where you re-use(!) the Lehui picatinny.
cults3d
Rail Riser to suit Lehui Kriss Vector Gel Blaster Designed to replace the picatinny, print either the normal one and the picatinny or you can try the re-use picatinny, where you re-use(!) the Lehui picatinny.
myminifactory
The rear portion (30mm) of the Vector's rail was left open to allow the sling mount to move freely and not get obstructed by the rail. This version has countersinks for square M3 nuts (I had a bunch left over from a kit), but I will upload a version...
thingiverse
The rear portion (30mm) of the Vector's rail was left open to allow the sling mount to move freely and not get obstructed by the rail. This version has countersinks for square M3 nuts (I had a bunch left over from a kit), but I will upload a...
thingiverse
Kriss Vector Full Rail Riser for KWA Airsoft (Split for 20x20 printers) This is a remix of https://www.thingiverse.com/thing:2979362 which is also a remix of https://www.thingiverse.com/thing:1387670 Edits made include alterations to the arch which...
cults3d
This hand guard give a nice looking to the Kriss Vector and it's compatible with Ares, Krytac and Kva Kriss Vector airsoft replica. There is enough room to mount any silencer/suppressor as shown on photos. On both side the picatinny rails allow to...
cults3d
Hello there! ...Here you have Riser Picatinny Rail Mount, very useful for airsoft guns. ...It's only 3 parts easy to print and won't take long I hope you enjoy it!
thingiverse
1-Slip on rear slider and slide as far back as possible 2-Slip on second slider approx 85mm from the rear (this is just a stabilizing slider and does not need to be secured) 3-Slip on Rear Picatinny and use a m2 grub screw to secure it to the rear...
cults3d
... Vector Modular Handguard. ... Guaranteed Plug and Play Without Any Hassle. The File Comprises of - A MK1 Modular Rail - A Top 11 Tooth Picatinny Rail - A Bottom 12 Tooth Picatinny Rail You May Need : - 6 Pieces of JF (Flat Top) M4 Screws For The Rail
cults3d
You Will Need : - 2 Pieces Of M4 x 30mm For The Hand Stop - 4 Pieces Of M4 X 10mm For The Main Rail To The Kriss Vector - 10 Pieces of M4 X 8mm For The Picatinny Rail - 2 Pieces of M4 x 16mm For The QD Swivel Mount Pay Attention To The Above...
cults3d
DURING INSTALLATION, YOU DO NOT HAVE THE REMOVE THE STOCK BOTTOM PICATINNY RAIL OF THE KRISS VECTOR UNIT. ... The Design File Includes - A Short 3 Cm MK5 Handguard Rail - A Bottom 12 Tooth Picatinny Rail - One Each Left and Right 5 Tooth Picatinny Rail...
cults3d
This is modelled after the MK5 Handguard Modular Rail for The Kriss Vector, But Slightly Longer. Guaranteed Plug and Play, I Have Tried It on A KWA / KSC Kriss Vector GBBR, It Should Work with Krytac Kriss Vector AEG, But I Have Not Tried It Yet.
cults3d
The Design Comprises Of: - Main Rail - Primary Top Rail (11 Tooth Picatinny Rail) - Secondary Top Rail (9 Tooth Picatinny Rail) - Long Bottom Rail (19 Tooth Picatinny Rail) You Need The Following Screws : - 10 Pieces JF Type M4 x 8mm For Securing...
thingiverse
This three-part vector can be glued together to create a vector that extends and, if multiple are printed, can be connected at the ends or head-to-tail. None need supports--print the arrow arrow-side-down and the cap hole-side-down to ensure...
grabcad
Vector proposes a solution to the high flux of automobiles hitting the roads. As the economic activity grows in Pakistan so do the cars on the roads. More business = better economy = more people in a position to afford cars.One might suggest that the...