vpcok sous vide 3d models

A stand for a sous vide immersion heater produced by VPCOK. The pictures show a print of the original STL file, after which I discovered that despite all my measuring the bottom of the heater cylinder doesn't rest on the support as intended, and...

Sous Vide

Sous Vide case

anova sous vide ring for box

Sous Vide cover for 11" pot

Sous Vide Rack Parts for Assembly

anova sous vide ring for box

This is a replacement rack for a sous vide cooker

Sous Vide bracket for mounting in a Thermo Box container.

3D model of the sous vide cooker Anova

Mount for Anova Sous Vide (works for any 60mm sous vide device) https://www.buymeacoffee.com/jschaftenaar

This is a Sous Vide bracket for the Champion IPX7 WiFi Sous Vide Circulator to be mounted in the cover of a thermo box.

This adapter allows you to use a large container and your sous vide.

Simple wall mount for Sous Vide cooker. ... Hole diameter is 58 mm.

attempting to design a pump cover for sous vide immersion cooker

Based on instructable's recipe I made my sous vide device and designed a compact box for the electronics. I also posted about it here (in Hungarian). ... https://www.youmagine.com/designs/sous-vide-box

See https://lochte.github.io/posts/Sous_Vide/ for more details Design by: Mads Lykke Jensen Enjoy !

Witt Sous Vide Holder The part should be Rotated 90 Degres, before you Slice it. So it stands like on the Pictures. ...

I made this sous vide rack, it fits inside my cooler with space to the sous vide itself. Dimensions 280 x 150 x 150 mm (DxWxH). 2 options, printing all in place or separated parts. I tried both and think separated is better. I used superglue to...

Just a quick and not perfect remix that fits another model of the Anova Sous Vide with a rounded bottom. ...It does the job though with or without the clamp.

sous vide raft is an assistant raft to keep the ziplock orientated up and outside of the water Because of the high temperature, only print with ABS or PETG materials. ... not support required infill 15%-20%

An excellent clamp to hold on to those sous vide bags. My previous clamps were made of metal and tended to rust a little bit. These plastic clamps are perfect for the job. You need to print with supports. I printed mine with 100% infill out of PETG...

the plastic clips broke off of my wancle sous vide stick cap. ...So I made a replacement.</p><p>It has to be printed in some high temp material, I used nylon or in this case prusament pc-cf.</p>

I didn't have room for a wall mount that seems to be popular with this Sous Vide cooker. Instead I made a stand so that between uses it can sit on my count nicely and stay out of the way and keep clean. I didn't make it a complete sleeve...

... and the caps are pressed on to act as feet for M6 Hex Cap screws. (Allen Head). More information can be found on the Heatermeter forum here ...http://tvwbb.com/showthread.php?64200-Sous-Vide-Setup You'll need to print with supports for the case.

9-4-17 I float tested these at room temperature and had no water infiltration...however, the first cycle my son used them with the sous vide they all had water infiltrate and many just sunk to the bottom. So I changed this to a work in progress, I...

Compact sous vide box for xmt7100 pid controller. On the back side there is place for a rocker switch and 3 holes for power in cable, power out cable and thermocouple. On the bottom is place for a solid state relay. All holes are made such that M3...

Store the circulator in an upright position. Now with cable holder. Print instructionsUnassociated tags: sous vide Licence: Creative Commons - Attribution Category: Kitchen &amp; Dining Print Settings Notes: I printed the cable holder using the vase...

Can lifter for can 60mm and 80mm I used them for "crème brûlée" sous-vide Need 2x M3 plastic or stainless screws ( min 8mm max 15mm ) Tapping the junction hole before, or use first a metal screw to make the road, then you can use a plastic screw...

This is a collar I use to raise my Anova sous vide cooker so that it doesn't rest on the bottom of my cooler. It's an inch tall, which is perfect for raising it just off the bottom of an Igloo Island Breeze cooler. ...This works with the original lid...