wired earbud holder 3d models

Skullcandy wired earbuds holder. The skull looks good enough to hold non-Skullcandy wired earbuds. ... SPECS ========================== Length: 2.392" (6.076cm) Width: 1.982" (5.034cm) Height: 0.983" (2.497cm)

Screws on to a normal mic stand. ...Recommend very slow first few layers, with the headphone cone oriented downward.

The wire holder works well and it's very hard to pull the wire out accidentally, although the clip itself usually ends up coming off before the wire does. Main issue I found is that adding a clip doesn't completely solve the problems I ran into...

The wire holder works well and it's very hard to pull the wire out accidentally, although the clip itself usually ends up coming off before the wire does. Main issue I found is that adding a clip doesn't completely solve the problems I ran into and...

earbud holder

Earbud holder

These are earbud markers for iPhone wired earbuds.  If you are confusing or losing your earbuds to others in your houshold or office, this is the solution.  Clearly identify your earbuds with one of these unique markers. ... You can...

Perfect Minimalistic Universal Earbud Holder.

Universal Earbud Holder. Perfect. ...Minimalistic.

Insert the wires and wrap up your earbuds.

Simple yet effective earbud holder. ... I use it to store my earbuds when riding my motorbike.

Earbud holder- Supposed to be a cassette tape look alike.

An earbud holder/wrap that works four ways.

A minimalistic thing to wrap your earbuds around :D Fits earbuds with stem diameter about 5mm. ... _______________ Note: Put the earbuds on the clip from the wire first, then slide down the earbuds to increase durability.

Another earbud holder. ...I wanted to have something that was smaller than the usual earbud holders around and pin in place the jack pin. ... Enjoy !

Yet another earbud holder. Tired of your earbuds constantly getting tangled? Then this is the holder for you! efficiently store your headphones or earbuds and never untangled them again. ...

This is a earbud holder that can hold earbuds with buttons/mic module. ...It is a simple design that do the job.

A simple earbud holder that works for just about any type of earbuds you may have.  At 200 micros, it takes about 30 minutes to print.

Earphone holder experimental design - ideal for iPhone earbuds. Low poly. ... Enjoy!

The center cut outs were mainly meant to reduce amount of filament used and time printing but can also be used to loop the earbud around the wires if it doesn't make it all the way to one end. I used the cord length from my own earbuds so that it...

This is a earbud holder :) Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: Yes Supports: No

Earbud Spool Holder Print Settings Printer Brand: RepRap Printer: Prusa I3 Custom Resolution: 0,3 mm Infill: 20%

This is a earbud holder for standard Apple earbuds. I needed something to wrap my earbuds with, so I made this. Instructions Find a piece of wood and let her rip! ... This was made using CorelDraw X4,...

Yet another earbud holder. Not like we have enough of those here on Thingiverse, right? Well, I wanted something a bit different from the designs already available. ...

This project was made by an 8th grade student, Randall Pelton Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: Yes Supports: Yes Infill: 10% How I Designed This This earbud holder was created using OpenSCAD. ... This is the...

Holds your earbud cords (and if strong enough) your earbuds. Work in progress, still not fully tested. Includes OpenSCAD file so it can be adjusted to your needs. Done for a S-15-01-STIC from supermagnete.de in V1 Placeholder for a S-15-03-N...

... earbuds. ... Instructions Print it! The proportions may not be to your liking, but of course you can edit it here, using 123D Design Online: http://www.123dapp.com/smb-123D_Design/Earbud-Holder/1261768

There are two designs. ...The HD design uses thicker walls to withstand a little more abuse. Use this holder to put your earbuds in a binder or pocket and keep them from getting damaged.

This is a simple earbud holder found on Cults3D by the maker Glamarune. ...The link to the original file can be found below: https://cults3d.com/en/3d-model/gadget/mex-earphone-organizer

Simple print that will fit your earbuds perfectly.